Pages: [1] 2 3
Author Topic: tuning path NA S4  (Read 26022 times)
airtite
Hero Member
*****

Karma: +13/-3
Offline Offline

Posts: 741


« on: January 24, 2012, 02:07:22 AM »

Hi Guys

OK with my limited "software" tuning experience I have played around quite a bit with my turboed A4 now and once I acquire my S4 I would like too obviously squeeze as much potential from that awesome v8 as possible. Now when tuning a turboed car its mainly about achieving extra boost and that with optimal timing/fueling gives great increases in power, so with a NA motor whats the best way too tune them?
Logged
julex
Hero Member
*****

Karma: +79/-4
Offline Offline

Posts: 923


« Reply #1 on: January 24, 2012, 09:53:14 AM »

Not much really.

For one, aim at going richer and getting "best power" AFR which is around 12:1.
Secondly, advance timing to a bleeding edge of what motor can take.

That's it. And no, V8 is not that awesome (only saying since I have V6 with turbos Smiley)
Logged
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #2 on: January 24, 2012, 11:47:54 AM »

Build a RS4 motor.  DTM-style intake, larger intake manifolds, port/polish of cylinder head, lightening and balancing of the bottom end, dry-sump oiling, pulley reducers, lightweight flywheel / balancer, camshafts, valve-springs, fast-velocity headers, titanium exhaust, built fuel system.

Build a RS6 motor.  Heavy-duty clutch, lower compression ratio and connecting rods (?) re-build, rs6 turbo headers which probably dont fit thus requiring custom exhaust plumbing for the turbo, single versus dual-turbo decision, inter-cooler plumbing, water-meth plumbing, ecu reprogramming, etc.

Buy the APR Supercharger kit for $15,000.

Buy a Stage 3 B5 S4 Avant for $15,000.
« Last Edit: January 24, 2012, 12:07:49 PM by nehalem » Logged
airtite
Hero Member
*****

Karma: +13/-3
Offline Offline

Posts: 741


« Reply #3 on: January 25, 2012, 12:45:24 AM »

thanks guys
Logged
Snow Trooper
Hero Member
*****

Karma: +90/-24
Offline Offline

Posts: 689


WWW
« Reply #4 on: January 25, 2012, 08:44:43 PM »

Octane and timing
Logged

cartoons?
6A 61 72 65 64 40 76 6C 6D 73 70 65 63
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 539


« Reply #5 on: January 26, 2012, 02:18:12 PM »

get the .bin id be willing to help you on this
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12270


WWW
« Reply #6 on: January 26, 2012, 02:20:20 PM »

Sorry. The NA v8 isn't very responsive to tuning. Even with an SC it really isn't built for higher cylinder pressures.

Get an audi with a proper motor.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #7 on: January 26, 2012, 06:15:48 PM »

Sorry. The NA v8 isn't very responsive to tuning. Even with an SC it really isn't built for higher cylinder pressures.

Get an audi with a proper motor.

lol, you are harsh
Logged
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12270


WWW
« Reply #8 on: January 26, 2012, 08:25:48 PM »

Moral hazard man, moral hazard.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #9 on: January 26, 2012, 10:09:36 PM »

Moral hazard man, moral hazard.

I was looking for proper Cayenne 18Z rotors and wound up on the B6/B7 AZ forum.  Racingbrake apparently is making some bolt-on rotor and upon realizing they were planning on building it for the B6/B7 chassis, I wrote on the post:  "You should really make this rotor for a non-POS chassis.  This thread sucks."

LOL...  sorry OP.  TBH, I'd LOVE to build up a new 3.2 V6 into a single-turbo monster to be put into a B7 RS4 body...  <drool>
Logged
amd is the best
Sr. Member
****

Karma: +11/-5
Offline Offline

Posts: 269



« Reply #10 on: January 27, 2012, 11:37:21 AM »

Sorry. The NA v8 isn't very responsive to tuning. Even with an SC it really isn't built for higher cylinder pressures.

Get an audi with a proper motor.

A pretty ignorant statement....  Honda's weren't built for higher cylinder pressures either, but they work VERY well.

And an Audi with a proper "motor" would be an I5 vehicle.  Hope you weren't hinting at the inefficient 2.7tt.
Logged

2012 Golf TDI
2001 Audi A4 2.8 30v Supercharged
1991 Audi 200 20v
nyet
Administrator
Hero Member
*****

Karma: +608/-168
Online Online

Posts: 12270


WWW
« Reply #11 on: January 27, 2012, 12:33:16 PM »

I5 >> 2.7tt > v10 > 4.2tt > 3.0sc >> 2.0t > 1.8t > ..............................

way way down at the bottom somewhere is the NA v8 used in the S4, RS4 and S5

honda motors work just fine with high boost; you just have to build the motor.

2.7t and I5 don't need any internal work. stock block + internals are just fine.

I think we can all agree the I5 is definitely a proper motor.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
amd is the best
Sr. Member
****

Karma: +11/-5
Offline Offline

Posts: 269



« Reply #12 on: January 27, 2012, 12:40:02 PM »

I5 >> 2.7tt > v10 > 4.2tt > 3.0sc >> 2.0t > 1.8t > ..............................

way way down at the bottom somewhere is the NA v8 used in the S4, RS4 and S5

honda motors work just fine with high boost; you just have to build the motor.

2.7t and I5 don't need any internal work. stock block + internals are just fine.

I think we can all agree the I5 is definitely a proper motor.

Your list is right on spot with what I'd say!  I just don't understand why the V8 doesn't seem to repond well to boost.  Usually, engines that make decent power in N/A form have significant gains from boost.  Maybe it's poor tuning in their case?  Not sure.

As far as The Honda's go, internals are certainly advised however my friend had a bone stock 170k miles GSR with a GT3076 slapped on it and made 501whp.  Then went to the track and ran back to back 11.1's @ 129mph.  Who knows how long it would last like that though.

I <3 my I5!
Logged

2012 Golf TDI
2001 Audi A4 2.8 30v Supercharged
1991 Audi 200 20v
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #13 on: January 27, 2012, 02:34:14 PM »

I <3 my I5!

beast
Logged
amd is the best
Sr. Member
****

Karma: +11/-5
Offline Offline

Posts: 269



« Reply #14 on: January 27, 2012, 02:50:26 PM »

beast

http://nefariousmotorsports.com/forum/index.php?topic=1294.0title=  Grin
Logged

2012 Golf TDI
2001 Audi A4 2.8 30v Supercharged
1991 Audi 200 20v
Pages: [1] 2 3
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.023 seconds with 18 queries. (Pretty URLs adds 0s, 0q)