Pages: [1] 2
Author Topic: can someone help immo off me7.1.1 2.5l VW Jetta ECU  (Read 11352 times)
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« on: April 14, 2019, 05:23:42 PM »

My original ecu is bricked and I got one at the junkyard and read it via KTag and now i just need immo delete for ive tried. any help is greatly appreciated. I've attached all the KTag reads from the ecu. Thanks again in advance.
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #1 on: April 14, 2019, 05:26:15 PM »

Not for some... (mk5 2.5 and beetle 2.5).... I have 95160 Audi dumps that I can parse with the tool, and several 2.5 VW 95160 that cannot.

The me7.1.1 2.5 VW 95160 is a bitch...

can i get immo off for this epprom file
Logged
_nameless
Hero Member
*****

Karma: +360/-1070
Offline Offline

Posts: 2911



« Reply #2 on: April 15, 2019, 04:18:21 AM »

how have you tried? its 4 bites including cks, all vag me7 eeproms have the same layout
Logged

If you are broke or expecting free handouts DO NOT message me. I'll probably put you on blast if you do.
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #3 on: April 15, 2019, 09:06:54 PM »

I have tried with KTag and mpps with no luck writing back to iepprom. I get a communication error unles I right the file back that I read originally.
Logged
_nameless
Hero Member
*****

Karma: +360/-1070
Offline Offline

Posts: 2911



« Reply #4 on: April 16, 2019, 06:29:58 AM »

I've done these with ktag before in the past without issue, are you using the blue lead to keep the ecu on bootmode? Or you need to remove a 0k ohm resistor from the back of the ecu
Logged

If you are broke or expecting free handouts DO NOT message me. I'll probably put you on blast if you do.
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #5 on: April 16, 2019, 06:54:47 AM »

I used the grey alligator cable per instructions and I haven’t taken the resistor  off. The weird thing is I can read it all day but can’t right back to epprome unless it’s the original eeptom. Please help I lost the original file so I got a ecu from junkyard and I need to get this car running. 
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #6 on: April 16, 2019, 11:52:19 AM »

can you immo off this attached eeprom file please.
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #7 on: April 16, 2019, 02:26:31 PM »

can someone help me with immo off for this file i read the eeprome section with KTag but it shows all FF across the file. Please help and or advise. Thanks in Advance.
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #8 on: April 16, 2019, 02:29:14 PM »

i see several 0Hm resistors which sohould i remove?
Logged
vwaudiguy
Hero Member
*****

Karma: +54/-37
Offline Offline

Posts: 2024



« Reply #9 on: April 16, 2019, 03:38:30 PM »

can you immo off this attached eeprom file please.

Your file is all FF. This means "there's nothing there".
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Breacking
Jr. Member
**

Karma: +0/-7
Offline Offline

Posts: 31


« Reply #10 on: April 17, 2019, 02:03:11 AM »

Привет. Почему бы тебе не воспользоваться VisualME7Logger?
Logged
adam-
Hero Member
*****

Karma: +125/-33
Offline Offline

Posts: 2181


« Reply #11 on: April 17, 2019, 02:12:36 AM »

What would that show?
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #12 on: April 17, 2019, 02:53:34 PM »

Oh my so how can i write the eeprom back on and with the immo off. It's strange because i read it with ktag and that's what it read but it wont allow me to write back on keep saying communication error unless I write what i read from the ecu.
.
Logged
BlackT
Hero Member
*****

Karma: +80/-42
Offline Offline

Posts: 1474



« Reply #13 on: April 17, 2019, 03:18:19 PM »

Oh my so how can i write the eeprom back on and with the immo off. It's strange because i read it with ktag and that's what it read but it wont allow me to write back on keep saying communication error unless I write what i read from the ecu.
.
for God sake don't write file with FF only in your eeprom.
First read it correct
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #14 on: April 17, 2019, 04:35:33 PM »

Every time i read it and open the file in hexedit thats all it gives me my apologies for any confusion but i am stuck at this point so any help would be greatly appreciated.
Logged
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 4.337 seconds with 16 queries. (Pretty URLs adds 0s, 0q)