Pages: [1] 2
Author Topic: can someone help immo off me7.1.1 2.5l VW Jetta ECU  (Read 483 times)
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« on: April 14, 2019, 05:23:42 PM »

My original ecu is bricked and I got one at the junkyard and read it via KTag and now i just need immo delete for ive tried. any help is greatly appreciated. I've attached all the KTag reads from the ecu. Thanks again in advance.
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #1 on: April 14, 2019, 05:26:15 PM »

Not for some... (mk5 2.5 and beetle 2.5).... I have 95160 Audi dumps that I can parse with the tool, and several 2.5 VW 95160 that cannot.

The me7.1.1 2.5 VW 95160 is a bitch...

can i get immo off for this epprom file
Logged
Marty
Hero Member
*****

Karma: +126/-81
Offline Offline

Posts: 1303


« Reply #2 on: April 15, 2019, 04:18:21 AM »

how have you tried? its 4 bites including cks, all vag me7 eeproms have the same layout
Logged

yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #3 on: April 15, 2019, 09:06:54 PM »

I have tried with KTag and mpps with no luck writing back to iepprom. I get a communication error unles I right the file back that I read originally.
Logged
Marty
Hero Member
*****

Karma: +126/-81
Offline Offline

Posts: 1303


« Reply #4 on: April 16, 2019, 06:29:58 AM »

I've done these with ktag before in the past without issue, are you using the blue lead to keep the ecu on bootmode? Or you need to remove a 0k ohm resistor from the back of the ecu
Logged

yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #5 on: April 16, 2019, 06:54:47 AM »

I used the grey alligator cable per instructions and I haven’t taken the resistor  off. The weird thing is I can read it all day but can’t right back to epprome unless it’s the original eeptom. Please help I lost the original file so I got a ecu from junkyard and I need to get this car running. 
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #6 on: April 16, 2019, 11:52:19 AM »

can you immo off this attached eeprom file please.
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #7 on: April 16, 2019, 02:26:31 PM »

can someone help me with immo off for this file i read the eeprome section with KTag but it shows all FF across the file. Please help and or advise. Thanks in Advance.
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #8 on: April 16, 2019, 02:29:14 PM »

i see several 0Hm resistors which sohould i remove?
Logged
vwaudiguy
Hero Member
*****

Karma: +47/-35
Offline Offline

Posts: 1968



« Reply #9 on: April 16, 2019, 03:38:30 PM »

can you immo off this attached eeprom file please.

Your file is all FF. This means "there's nothing there".
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
Breacking
Newbie
*

Karma: +0/-4
Offline Offline

Posts: 16


« Reply #10 on: April 17, 2019, 02:03:11 AM »

Привет. Почему бы тебе не воспользоваться VisualME7Logger?
Logged
adam-
Hero Member
*****

Karma: +84/-23
Offline Offline

Posts: 1763


« Reply #11 on: April 17, 2019, 02:12:36 AM »

What would that show?
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #12 on: April 17, 2019, 02:53:34 PM »

Oh my so how can i write the eeprom back on and with the immo off. It's strange because i read it with ktag and that's what it read but it wont allow me to write back on keep saying communication error unless I write what i read from the ecu.
.
Logged
BlackT
Sr. Member
****

Karma: +7/-2
Offline Offline

Posts: 268



« Reply #13 on: April 17, 2019, 03:18:19 PM »

Oh my so how can i write the eeprom back on and with the immo off. It's strange because i read it with ktag and that's what it read but it wont allow me to write back on keep saying communication error unless I write what i read from the ecu.
.
for God sake don't write file with FF only in your eeprom.
First read it correct
Logged
yoswann
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 18


« Reply #14 on: April 17, 2019, 04:35:33 PM »

Every time i read it and open the file in hexedit thats all it gives me my apologies for any confusion but i am stuck at this point so any help would be greatly appreciated.
Logged
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 19 queries. (Pretty URLs adds 0s, 0q)