Pages: [1]
Author Topic: 1.8T AWM VVT Delete  (Read 5958 times)
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« on: April 25, 2019, 10:34:54 PM »

Unplugged solenoid.

CDNWS changed to 0.
KFNWSE whole table set to 18.
ESKONF AA FF 00 30 FF FB 30 changed to AA FF 00 30 FF FB 33
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.


Getting a P0010 - "A" Camshaft Position Actuator Circuit (Bank 1) now.  Ideas?
Logged

aleks19411
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 60


« Reply #1 on: April 26, 2019, 01:35:21 AM »

Translate these more cards to 18
KFNWSE, KFNWKHE, KFNWKRE — maps 16x8.
KFNWKHLLE
as well as the second esconf (there are two of them)
both before the card KFKHFM set the AA FF 00 30 FF F8 33
number of software would indicate
« Last Edit: April 26, 2019, 01:37:59 AM by aleks19411 » Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #2 on: April 26, 2019, 01:52:44 AM »

For AWT I only change CDNWS to 0.
I think ESKONF doesen't have relationship with that DTC.it is only when you have hardware DTC
Logged
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« Reply #3 on: April 29, 2019, 01:47:29 PM »

Update:

Unplugged solenoid.

CDNWS changed to 0.
KFNWSE, KFNWKHE, KFNWKRE, KFNWKHLLE change to 18.
Both ESKONF maps changed from AA FF 00 30 FF FB 30 to AA FF 00 30 FF FB 33.
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.

Getting a P0010 - "A" Camshaft Position Actuator Circuit (Bank 1) still.

This error code goes away if I plug back in the solenoid but eventually I'd like to install one that doesn't have the solenoid.
Logged

BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #4 on: April 29, 2019, 01:57:35 PM »

Maybe your CDNWS is not at corect adress. Post jor ecu bin
Logged
aleks19411
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 60


« Reply #5 on: April 30, 2019, 12:36:58 AM »

Update:

Unplugged solenoid.

CDNWS changed to 0.
KFNWSE, KFNWKHE, KFNWKRE, KFNWKHLLE change to 18.
Both ESKONF maps changed from AA FF 00 30 FF FB 30 to AA FF 00 30 FF FB 33.
Copied KFZW to KFZW2 and KFZWOP to KFZWOP2.

Getting a P0010 - "A" Camshaft Position Actuator Circuit (Bank 1) still.


This error code goes away if I plug back in the solenoid but eventually I'd like to install one that doesn't have the solenoid.
Put the firmware here, we'll see.
Logged
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« Reply #6 on: May 02, 2019, 10:29:44 PM »

Maybe your CDNWS is not at corect adress. Post jor ecu bin

Attached
Logged

BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #7 on: May 06, 2019, 06:38:36 AM »

CDNWS at 181AF
Logged
dal
Full Member
***

Karma: +6/-7
Offline Offline

Posts: 189



WWW
« Reply #8 on: May 06, 2019, 07:49:03 AM »

For AWT I only change CDNWS to 0.
I think ESKONF doesen't have relationship with that DTC.it is only when you have hardware DTC

I have done the wideband conversion on my car. Mine was 512kb without VVT. I only got the STFT/LTFT functions to work after I disabled the VVT solenoid on ESKONF.
In my case...
Logged

Audi A3 8L
1984cc stroker - E100 - ME7 wideband converted - 400whp target
Instagram: @a3stroker
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« Reply #9 on: May 09, 2019, 10:10:02 PM »

CDNWS at 181AF

Yeah that's the location I found it at too.   Original value is 02 changed to 00.
Logged

BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #10 on: May 09, 2019, 10:53:01 PM »

For AWT I only change CDNWS to 0.
I think ESKONF doesen't have relationship with that DTC.it is only when you have hardware DTC
My bad i didn't read it well, that dtc is connected to ESKONF. Did you change second ESKONF?
Logged
aleks19411
Full Member
***

Karma: +4/-4
Offline Offline

Posts: 60


« Reply #11 on: May 14, 2019, 12:06:30 PM »

Yes. he wrote that he changed two eskonf
Logged
Jerry Tunin
Full Member
***

Karma: +4/-1
Offline Offline

Posts: 121



WWW
« Reply #12 on: May 20, 2019, 09:55:42 PM »

My bad i didn't read it well, that dtc is connected to ESKONF. Did you change second ESKONF?

Yep
Logged

Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.044 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)