gin+
Jr. Member
Karma: +2/-1
 Offline
Posts: 39
|
 |
« on: May 07, 2019, 12:04:59 PM »
|
|
|
My post cat 02 sensor went bad and I thought it would be a good time to attempt a code out considering I'm cat-less. I believe I've followed all the wiki steps, everything appears fine (no faults) and logs seem normal. My issue is readiness won't set. What I haven't been able to try is the VCDS readiness wizard as I'm using VCDS lite and that feature is not available. I'm not sure if that would help or not. I see some guys talking about ASM patches, but that's over my head, for now at least. Being that I'd rather not buy a replacement sensor I might be open to some paid assistance from a reputable forum member.
|
|
|
|
|
Logged
|
|
|
|
|
gt-innovation
|
|
« Reply #1 on: May 07, 2019, 01:23:02 PM »
|
|
|
you can set readiness on me7 without asm patches...search this forum a bit better.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #2 on: May 07, 2019, 01:23:51 PM »
|
|
|
My post cat 02 sensor went bad and I thought it would be a good time to attempt a code out considering I'm cat-less. I believe I've followed all the wiki steps, everything appears fine (no faults) and logs seem normal. My issue is readiness won't set. What I haven't been able to try is the VCDS readiness wizard as I'm using VCDS lite and that feature is not available. I'm not sure if that would help or not. I see some guys talking about ASM patches, but that's over my head, for now at least. Being that I'd rather not buy a replacement sensor I might be open to some paid assistance from a reputable forum member.
Can you list what you have tried? I have reorganized the s4wiki some |
|
|
|
|
Logged
|
|
|
|
gin+
Jr. Member
Karma: +2/-1
Offline
Posts: 39
|
|
« Reply #3 on: May 08, 2019, 10:30:23 AM »
|
|
|
I certainly appreciate any input.
This is where I'm at, sensor is currently disconnected.
CDKAT - 0
CDHSH - 0
CDHSHE - 0
CDLATV - 0
CDLASH - 0
CDLSH - 0
CWKONLS - 1
CLRSHK - 5
ESKONF Byte 3 F0
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #4 on: May 08, 2019, 01:16:38 PM »
|
|
|
You can try CWKONABG.0 = 0..
also double check your ESKONF (I do not know off hand if that is correct for AK, maybe others can chime in).
|
|
|
|
|
Logged
|
|
|
|
gin+
Jr. Member
Karma: +2/-1
Offline
Posts: 39
|
|
« Reply #5 on: May 09, 2019, 07:54:24 AM »
|
|
|
You can try CWKONABG.0 = 0..
also double check your ESKONF (I do not know off hand if that is correct for AK, maybe others can chime in).
I already changed CWKONABG, I forgot to include it in my previous post  . I'm pretty sure ESK is correct as I was struggling with it at first. I learned there are separate addresses for what I believe would be for manual or auto trans. Perhaps I need to figure out the location of SRYLS? Readiness byte? |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #6 on: May 09, 2019, 08:38:09 AM »
|
|
|
Possibly, but I think something else is wrong, that list should have worked.
|
|
|
|
|
Logged
|
|
|
|
Risky
Full Member
Karma: +4/-0
Offline
Posts: 107
|
|
« Reply #7 on: May 09, 2019, 01:49:43 PM »
|
|
|
Double check make sure it's defined correctly. IMO, defining emission code words can be a headache.
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +177/-18
Offline
Posts: 1402
mk4 1.8T AUM
|
|
« Reply #8 on: May 09, 2019, 04:41:31 PM »
|
|
|
CLRSHK 16 -> 17
this list should set readiness so ++ to check definition
vcds group 36 should be 0.0v test ok
same with 46 for a cat
|
|
|
|
|
Logged
|
|
|
|
gin+
Jr. Member
Karma: +2/-1
Offline
Posts: 39
|
|
« Reply #9 on: May 09, 2019, 05:38:03 PM »
|
|
|
Thanks guys. I'll re-group and see if I can't find something that I may have overlooked.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #10 on: May 09, 2019, 07:24:23 PM »
|
|
|
What specifically isn't passing readiness? If it is post cat, it shouldn't even try to pass readiness, it should come back unsupported (and readiness)
|
|
|
|
|
Logged
|
|
|
|
gin+
Jr. Member
Karma: +2/-1
Offline
Posts: 39
|
|
« Reply #11 on: May 10, 2019, 08:10:12 PM »
|
|
|
Oxygen sensors and secondary air injection show no love. I made a revision so there's a chance it hasn't had enough running time but I'm guessing I've driven it enough. I have mslub and mslbas zero'd out and n112 doesn't open after CWKONABG.0 = 0.
|
|
|
|
|
Logged
|
|
|
|
gin+
Jr. Member
Karma: +2/-1
Offline
Posts: 39
|
|
« Reply #12 on: May 11, 2019, 05:59:40 PM »
|
|
|
I cleared CDSLS and CDLSV but of course catalyst, oxygen sensors, and SAI show unsupported with my generic scan tool. Not sure if that'll be an issue with NYS inspection or not  |
|
|
|
|
Logged
|
|
|
|
gin+
Jr. Member
Karma: +2/-1
Offline
Posts: 39
|
|
« Reply #13 on: May 23, 2019, 02:09:30 PM »
|
|
|
I was able to pass  |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #14 on: May 23, 2019, 02:30:48 PM »
|
|
|
Thanks for the update!
|
|
|
|
|
Logged
|
|
|
|
|
