Pages: [1] 2
Author Topic: 1.8t 518AK - Post cat 02 sensor readiness  (Read 8300 times)
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« on: May 07, 2019, 12:04:59 PM »

My post cat 02 sensor went bad and I thought it would be a good time to attempt a code out considering I'm cat-less.  I believe I've followed all the wiki steps, everything appears fine (no faults) and logs seem normal.  My issue is readiness won't set.  What I haven't been able to try is the VCDS readiness wizard as I'm using VCDS lite and that feature is not available.  I'm not sure if that would help or not.  I see some guys talking about ASM patches, but that's over my head, for now at least.  Being that I'd rather not buy a replacement sensor I might be open to some paid assistance from a reputable forum member.

Logged
gt-innovation
Sr. Member
****

Karma: +60/-91
Offline Offline

Posts: 449


« Reply #1 on: May 07, 2019, 01:23:02 PM »

you can set readiness on me7 without asm patches...search this forum a bit better.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #2 on: May 07, 2019, 01:23:51 PM »

My post cat 02 sensor went bad and I thought it would be a good time to attempt a code out considering I'm cat-less.  I believe I've followed all the wiki steps, everything appears fine (no faults) and logs seem normal.  My issue is readiness won't set.  What I haven't been able to try is the VCDS readiness wizard as I'm using VCDS lite and that feature is not available.  I'm not sure if that would help or not.  I see some guys talking about ASM patches, but that's over my head, for now at least.  Being that I'd rather not buy a replacement sensor I might be open to some paid assistance from a reputable forum member.



Can you list what you have tried? I have reorganized the s4wiki some
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« Reply #3 on: May 08, 2019, 10:30:23 AM »

I certainly appreciate any input.

This is where I'm at, sensor is currently disconnected.

CDKAT - 0
CDHSH - 0
CDHSHE - 0
CDLATV - 0
CDLASH - 0
CDLSH - 0
CWKONLS - 1
CLRSHK - 5
ESKONF Byte 3 F0
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #4 on: May 08, 2019, 01:16:38 PM »

You can try CWKONABG.0 = 0..


also double check your ESKONF (I do not know off hand if that is correct for AK, maybe others can chime in).
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« Reply #5 on: May 09, 2019, 07:54:24 AM »

You can try CWKONABG.0 = 0..


also double check your ESKONF (I do not know off hand if that is correct for AK, maybe others can chime in).

I already changed CWKONABG, I forgot to include it in my previous post  Embarrassed.

I'm pretty sure ESK is correct as I was struggling with it at first.  I learned there are separate addresses for what I believe would be for manual or auto trans.

Perhaps I need to figure out the location of SRYLS?  Readiness byte?
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #6 on: May 09, 2019, 08:38:09 AM »

Possibly, but I think something else is wrong, that list should have worked.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Risky
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 107


« Reply #7 on: May 09, 2019, 01:49:43 PM »

Double check make sure it's defined correctly. IMO, defining emission code words can be a headache.
Logged
fknbrkn
Hero Member
*****

Karma: +186/-24
Online Online

Posts: 1454


mk4 1.8T AUM


« Reply #8 on: May 09, 2019, 04:41:31 PM »

CLRSHK 16 -> 17
this list should set readiness so ++ to check definition

vcds group 36 should be 0.0v test ok
same with 46 for a cat
Logged
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« Reply #9 on: May 09, 2019, 05:38:03 PM »

Thanks guys.  I'll re-group and see if I can't find something that I may have overlooked.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #10 on: May 09, 2019, 07:24:23 PM »

What specifically isn't passing readiness? If it is post cat, it shouldn't even try to pass readiness, it should come back unsupported (and readiness)
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« Reply #11 on: May 10, 2019, 08:10:12 PM »

Oxygen sensors and secondary air injection show no love.  I made a revision so there's a chance it hasn't had enough running time but I'm guessing I've driven it enough.  I have mslub and mslbas zero'd out and n112 doesn't open after CWKONABG.0 = 0. 
Logged
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« Reply #12 on: May 11, 2019, 05:59:40 PM »

I cleared CDSLS and CDLSV but of course catalyst, oxygen sensors, and SAI show unsupported with my generic scan tool.  Not sure if that'll be an issue with NYS inspection or not Huh  
Logged
gin+
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 39


« Reply #13 on: May 23, 2019, 02:09:30 PM »

I was able to pass  Grin
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #14 on: May 23, 2019, 02:30:48 PM »

Thanks for the update!
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)