zaoxdk
Jr. Member
Karma: +0/-1
 Offline
Posts: 34
|
 |
« on: October 06, 2019, 01:30:17 AM »
|
|
|
Hello
I have had problems with not achieving the correct boost (file set to 1.1 bar) car only boosts 0.5-0.6 which is the wastegate opening pressure. The turbo which I have mounted is a K04-015. I have checked that it has the same wastegate opening pressure as on the Stock turbo.
Car is a A4 B6 1.8t BFB, 518AL. When disconnecting the wastegate actuator hose from N75, it boosts fine (above 1.1 ofc). The N75 is mounted as it should, triple checked that. It’s a brand new OE unit.
No boost leaks, have FMIC or restrictions in exhaust.
Has anyone experienced the same?
Thanks
|
|
|
|
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +177/-18
Offline
Posts: 1401
mk4 1.8T AUM
|
|
« Reply #1 on: October 06, 2019, 02:46:24 AM »
|
|
|
it should push much more than 1.1 wo actuator line
post logs etc
|
|
|
|
|
Logged
|
|
|
|
zaoxdk
Jr. Member
Karma: +0/-1
Offline
Posts: 34
|
|
« Reply #2 on: October 06, 2019, 03:47:43 AM »
|
|
|
It does. Haven’t got any logs yet. Got it pushing at least 1.5 on the dyno W/O wastegate actuator line, but I let it off as I am on stock rods.
|
|
|
|
|
Logged
|
|
|
|
|
|
zaoxdk
Jr. Member
Karma: +0/-1
Offline
Posts: 34
|
|
« Reply #4 on: October 06, 2019, 02:36:11 PM »
|
|
|
Will get some logs then. Sorry for breaking forum rulles.
|
|
|
|
« Last Edit: October 06, 2019, 02:45:06 PM by zaoxdk »
|
Logged
|
|
|
|
zaoxdk
Jr. Member
Karma: +0/-1
Offline
Posts: 34
|
|
« Reply #5 on: October 10, 2019, 02:24:47 AM »
|
|
|
Problem solved. Fitted N75 valve from a A3 8P 2.0tfsi. OE num: 06F906283F. Had to rewire the plug to a different D type connector. This valve is also much cheaper than the old style n75. Car boosts fine and holds at 1.1 as programmed.
System has been tested up to 2.5 bar - no leaks were found.
For some odd reason, the brand new OEM N75 which i had fitted must have had some problems, as it simply wouldn’t bleed enough air into the atmospheric pressure pipe.Measuring pressure at 95% n75 duty cycle at actutator connection (T pipe to a pressure gauge) resulted in 0.4-0.5 which is more than enough to open the wastegate.
Wastegate has been checked with a pressure gun, and has same opening pressure (0.5) as Stock turbo.
For any more info, please ask.
|
|
|
|
|
Logged
|
|
|
|
|
_nameless
|
|
« Reply #6 on: October 10, 2019, 05:11:56 AM »
|
|
|
Do an output test with vcds verify its working. Did you wore it backwards? They wont work right if polarity is incorrect
|
|
|
|
|
Logged
|
If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/ |
|
|
zaoxdk
Jr. Member
Karma: +0/-1
Offline
Posts: 34
|
|
« Reply #7 on: October 10, 2019, 06:14:39 AM »
|
|
|
Yes, it is functioning as it should, dutycycle is not as High as on the Stock n75, while boost request matches boost actual. Has been wired correctly, checked polarity on diagram and valve
|
|
|
|
|
Logged
|
|
|
|
|
