NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > about me7_95040 1.31 and 1.4 problem
Pages: [1]
« previous next »
Author Topic: about me7_95040 1.31 and 1.4 problem  (Read 3018 times)
raffeale
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« on: January 14, 2020, 01:28:21 AM »
today I used me7_95040  to read ecu through obd interface but I got error messages, it is failed in initiating  communication  error =0x07
what's wrong?

I change  baudrate  to 57600 and the result  was same.

the steps is
turned on dashboard
plugin kkl cable with ft 232rl chipset
run me _95040  --ODB -p 3 -r test.bin
 I got error =0x07


I have installed the newest driver for kkl cable from from ftd website
the port number  is right ,I found it in windows device management.


« Last Edit: January 14, 2020, 01:36:22 AM by raffeale » Logged
raffeale
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #1 on: January 14, 2020, 01:38:13 AM »
Quote from: raffeale on January 14, 2020, 01:28:21 AM
today I used me7_95040  to read ecu through obd interface but I got error messages, it is failed in initiating  communication  error =0x07
what's wrong?

I change  baudrate  to 57600 and the result  was same.

the steps is
turned on dashboard
plugin kkl cable with ft 232rl chipset
run me _95040  --ODB -p 3 -r test.bin
 I got error =0x07


I have installed the newest driver for kkl cable from from ftd website
the port number  is right ,I found it in windows device management.



Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1600
« Reply #2 on: January 14, 2020, 05:06:32 AM »
bootmode will work
there is a whole thread for this tool btw
Logged
dilly
Sr. Member
****

Karma: +12/-36
Offline Offline

Posts: 304
« Reply #3 on: January 14, 2020, 11:41:34 AM »
i get an error like yours when i run the program with no cable connected. perhaps your drivers are wrong. here is a gui version if you would like to try for shits and giggles. it has version 1.31 and 1.4 in it. just run me7gui. sometimes i had troubles with the command line so i just use gui whenever i can
Logged
raffeale
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #4 on: January 14, 2020, 07:17:40 PM »
Quote from: dilly on January 14, 2020, 11:41:34 AM
i get an error like yours when i run the program with no cable connected. perhaps your drivers are wrong. here is a gui version if you would like to try for shits and giggles. it has version 1.31 and 1.4 in it. just run me7gui. sometimes i had troubles with the command line so i just use gui whenever i can

I have got an other error code when I use this tools without connection,  I am pretty sure that my driver is ok, because the com port can be found in windows device management.
when I.try to connected a port that  don't exist , it will  appear other error code.
Logged
raffeale
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #5 on: January 14, 2020, 07:18:45 PM »
Quote from: aef on January 14, 2020, 05:06:32 AM
bootmode will work
there is a whole thread for this tool btw

my ecu is 81 pins bosch me7,I dont know which pin is boot pin ?
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1600
« Reply #6 on: January 15, 2020, 02:14:40 AM »
use the board and the search to find out

everything is there, your lazy
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 24, 2024, 06:54:44 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.016 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)