stretchmyjerky
Newbie
Karma: +0/-8
 Offline
Posts: 14
|
 |
« on: March 03, 2020, 10:56:21 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
 |
« Reply #1 on: March 03, 2020, 10:58:25 AM »
|
|
|
Doubtful your file has it.
The defs are there for files that have the commonly used ASM patch.
|
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #2 on: March 03, 2020, 11:02:53 AM »
|
|
|
But then why does it have parameters set for example launch RPM is set to 2304rpm and accelerator pedal threshold is 48% and the minimal spark start time (FTOMN) is set to 0.2ms and the speed threshold is 3km/h.
The car has been slightly modified (not properly might i add) It has a K04 hybrid, full turbo back milltek exhaust and was dyno'd at 286hp
|
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #3 on: March 03, 2020, 11:08:03 AM »
|
|
|
might i add, i would love to have that functionality but honestly have no idea where to start to get it on there. I'm new to the TFSI / MED9 scene. most of the guides are basically just gibberish to me xD I do have a KESS v2 from when i had my passat and used that to get the file off the ECU
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #4 on: March 03, 2020, 11:09:06 AM »
|
|
|
Ya, could be it was added.
|
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #5 on: March 03, 2020, 11:12:01 AM »
|
|
|
but then how would i go about using it. I wasn't told anything by the previous owner. The car also has aftermarket cruise control with an aftermarket clutch switch. Would that have anything to do with it?
|
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #6 on: March 03, 2020, 11:36:28 AM »
|
|
|
Is nobody able to help with an answer then?
|
|
|
|
|
Logged
|
|
|
|
|
IamwhoIam
|
|
« Reply #7 on: March 03, 2020, 11:38:20 AM »
|
|
|
If you don't post an actual file, how could anyone know and help you with an answer? I'm sorry but my crystal ball isn't answering just now.
|
|
|
|
|
Logged
|
I have no logs because I have a boost gauge (makes things easier)
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #8 on: March 03, 2020, 11:40:35 AM »
|
|
|
This is my file i got off my ECU
|
|
|
|
|
Logged
|
|
|
|
|
k0mpresd
|
|
« Reply #9 on: March 03, 2020, 11:52:14 AM »
|
|
|
Ok, so i have an octavia VRS and got the map file from it. Did a bit of looking around and came across a Definitions file for "my ECU" (it's actually for a golf) and on that file there is a folder named "AL/NLS" and in that folder there are things symbolising launch control and no lift shift.
Is nobody able to help with an answer then?
way to be patient there. a big 40 minutes between original post and losing it no one has replied yet. |
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #10 on: March 03, 2020, 11:56:47 AM »
|
|
|
you have a point. My bad  |
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #11 on: March 03, 2020, 12:00:03 PM »
|
|
|
way to be patient there. a big 40 minutes between original post and losing it no one has replied yet.
After reading a little, i came across this "0x1A34B: Change FTOMN "minimum opening time" to 0 to enable anti-lag and no-lift shift." Is that literally all i have to do?  |
|
|
|
|
Logged
|
|
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #13 on: March 03, 2020, 02:25:51 PM »
|
|
|
Anybody have any advise??
|
|
|
|
|
Logged
|
|
|
|
stretchmyjerky
Newbie
Karma: +0/-8
Offline
Posts: 14
|
|
« Reply #14 on: March 03, 2020, 02:30:32 PM »
|
|
|
If you don't post an actual file, how could anyone know and help you with an answer? I'm sorry but my crystal ball isn't answering just now.
Here is the file |
|
|
|
|
Logged
|
|
|
|
|
