NefMoto > General > General Discussion > VW Passat VDO Dash problem
Pages: [1]
« previous next »
Author Topic: VW Passat VDO Dash problem  (Read 4639 times)
nicktruman
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 15
« on: April 16, 2020, 06:47:23 AM »
hi everyone.
i have fitted a 2002 20v 1.8t VW Passat engine and transaxle mid-mounted in my 1978 Triumph Spitfire, the engine now sits where the differential used to sit, thanks to this site we have disabled the immobilizer and are currently getting rid of the airpump, evap, 2nd o2 sensor etc..
I have used a immo3 VDO dash from a Passat for its gauges, and i have a problem. the dash is looking for the abs and is throwing a wobbly. The digital display shows a huge red STOP and i can't get rid of it.

any ideas how I can code out the abs and other modules that my car doesn't have?
« Last Edit: April 16, 2020, 07:20:59 AM by nicktruman » Logged
nicktruman
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 15
« Reply #1 on: April 16, 2020, 06:53:55 AM »
Quote from: nicktruman on April 16, 2020, 06:47:23 AM
These are the errors I am getting
VCDS-Lite Version: Release 1.2
Thursday, 16 April 2020, 13:29:08:0
Control Module Part Number: 3B0 920 929
  Component and/or Version: KOMBI+WEGFAHRSP VDO V04
           Software Coding: 04415
            Work Shop Code: WSC 00000
                      VCID: E4BBAF936743
           Additional Info: WVWZZZ3BZ5P015545     VWZ7Z0D9949179
9 Faults Found:
00771 -  Fuel Level Sensor (G)
        30-00 -  Open or Short to Plus
00562 -  Sensor for Oil Level/Temperature (G266)
        30-00 -  Open or Short to Plus
00779 -  Outside Air Temp Sensor (G17)
        30-00 -  Open or Short to Plus
01128 -  Immobilizer Pickup Coil (D2)
        35-00 -   -
01176 -  Key
        07-00 -  Signal too Low
01177 -  Engine Control Unit
        64-10 -  Not Currently Testable - Intermittent
01316 -  ABS Control Module
        49-00 -  No Communications
01321 -  Control Module for Airbags (J234)
        49-00 -  No Communications
01336 -  Data Bus for Comfort System
        49-00 -  No Communications
« Last Edit: April 16, 2020, 07:25:35 AM by nicktruman » Logged
cessnas
Full Member
***

Karma: +2/-17
Offline Offline

Posts: 77
« Reply #2 on: April 16, 2020, 02:07:35 PM »
If you want to remove it completely, go into CAN Gateway and subtract 00002 with VCDS
Logged
cessnas
Full Member
***

Karma: +2/-17
Offline Offline

Posts: 77
« Reply #3 on: April 16, 2020, 02:13:45 PM »
If you want to remove airbags also remove 00004
Logged
nicktruman
Newbie
*

Karma: +2/-0
Offline Offline

Posts: 15
« Reply #4 on: April 17, 2020, 01:00:47 PM »
Thank you Cessnas
are these recode options documented anywhere so I can remove all the rest of the audi stuff... just want to leave engine ECU, dash and sensors
cheers nick
Logged
cessnas
Full Member
***

Karma: +2/-17
Offline Offline

Posts: 77
« Reply #5 on: April 18, 2020, 01:53:24 AM »
Pretty sure you can only remove ABS and Airbag on the 3BG chassis from the gateway module.
You can check ross tech's website for more info about coding the gateway module
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • April 26, 2024, 06:53:11 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.181 seconds with 16 queries. (Pretty URLs adds 0.001s, 0q)