Can someone confirm if the variables:pvdk_w, pus_w, fvpdkdsl_w, fho_w, frhodkr_w, and SDLDSUA axis calculation have been changed correctly using IDA in this bin?? The rest of the BIN is bone stock so ALL of the maps will need scaled as in the outline, but if the ASM stuff has been done correctly in IDA this will be an excellent starting point for the 1.8T guys (myself included) as I have verified 032PL can be crossflashed to 032HS without immo off.

Thank you

Justin

Thanks Nyet.

Thank you for taking the initiative. It is appreciated and valued.

Sadly, I may not have a chance to look at your bin since it would require me also getting IDA up and set up with that BIN

Everything is in the right place, except the SDLDSUA axis.

In ME7.5 we have KFSDLDSUA and its axis is not hard-coded. Its a 16x6 map, located at 15B32 in your file. X-axis, witch is pressure, is located at 15B12. Y-axis is at 15B0C.

I didn't opened the XDF to check.

The address I gave are based on disassembling and they are correct.

Hopefully can keep this project going. I think I have found the extras that you were missing.

0x1498E;"Integratorbeiwert für Saugrohrmodell (Dynamik)";"KISRM";"1x1"
0x27D3C;"Konstante für Regeneriermasse in Leitung TEV-Saugrohr bei Normdruck + Normtemp.";"KMLTESG";"1x1"
0x1C83E;"Ersatzwert für Umgebungsdruck";"PUE";"1x1"
0x1C816;"Delta Druckwert für Signalvergleich Ladedruck mit Umgebungsdruck";"DPDSVLU";"1x1"
0x1C840;"Umgebungsdruckbegrenzung minimal";"PUMN";"1x1"
0x1C842;"Umgebungsdruckbegrenzung maximal";"PUMX";"1x1"
0x1C846;"pvdk min. Schwelle für Fehlererkennung Ladedrucksensor";"PVDKMN";"1x1"
0x18A25;"Zeitkonstante für Filterung von pu und fho in GGDSU";"ZDSU";"1x1"
0x28A5A;"Ersatzwert für Umgebungsdruck für BKV";"PUEBKV";"1x1"
0x15B32;"Schwelle für dynamische Schubumluftventilsteuerung aktiv";"KFSDLDSUA";"16x6"


Uploaded KP. I was going to add them to the XDF but didnt want to step on any toes. I cant contribute much more than this but would love to learn about the ASM changes as I'm a noob with IDA.

What's the point in doing this on some obscure bin?

It's enough to do one bin for every bootrom and then crossflash ECU to it.
And I'm pretty sure there's a bin that's already done.

Updated the XDF with what I believe are the extra ones you were missing.

I'm unsure of ZDSU which is currently 3 seconds (supposed to sqrt and multiply by two gives 3.46, will only accept a value of 3 or 4) does this need to be changed or can it stay original?

Another i'm unsure of is KMLTESG - value in table is 0.00001600 but wont allow for it to be divided by two, it'll only accept zero or the original, can't go lower.

Hopefully someone more experienced may be able to clear this up.


PRJ - Would something like 06A906032HJ be a better option for cross compatibility? personally I don't mind which binary, i'd just like to learn how to do it so I can do the binary i'm using once i have the know how!