Problem: Boost is pulsing

Pages: [1]

« previous next »

Author

Topic: Problem: Boost is pulsing (Read 3646 times)

MetalForLive

Full Member

Karma: +0/-0
Offline

Offline

Posts: 82

	Problem: Boost is pulsing « on: October 02, 2020, 10:37:56 AM »

Hi,

I got a problem with my boost on partitial load until 0,9-1bar everything is fine, but then on partitial load and on WOT boost is pulsing.
WGDC is jumping between 85% and ~60%
I tryed to limit boost with KFLDRL to 85% WGDC and DIMX on WOT because my Turbos can run 2bar+
Does anyone have an idea what can cause this behavior?
Should I maybe set DIMX to 95 in the last row ?

Thanks in advance


« Last Edit: October 02, 2020, 10:41:54 AM by MetalForLive »	Logged

xXxCryxXx

Full Member

Karma: +3/-17
Offline

Offline

Posts: 156

	Re: Re: Problem: Boost is pulsing « Reply #1 on: October 02, 2020, 11:31:57 AM »

Quote from: MetalForLive on October 02, 2020, 10:37:56 AM

looks like the wastegate spring ist jumping... is he okay? Did you check it?

X-Boost Performance


	Logged

Auriaka

Full Member

Karma: +17/-2
Offline

Offline

Posts: 113

	Re: Problem: Boost is pulsing « Reply #2 on: October 02, 2020, 08:22:05 PM »

Whats load doing? Seems like a load cap ride. If it hits load cap it will pull duty and then feed back causing an oscillation


	Logged

MetalForLive

Full Member

Karma: +0/-0
Offline

Offline

Posts: 82

	Re: Problem: Boost is pulsing « Reply #3 on: October 04, 2020, 06:38:25 AM »

Wastegates are okay.

its any issue with load, but I am not sure when this starts and why this happens.


	Logged

nyet

Administrator
Hero Member

Karma: +604/-167
Offline

Offline

Posts: 12235

	Re: Problem: Boost is pulsing « Reply #4 on: October 04, 2020, 09:24:35 AM »

have you tuned KFVPDKS/E?

https://s4wiki.com/wiki/Tuning#Base_boost_and_wastegate_spring_pressure


	Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.

MetalForLive

Full Member

Karma: +0/-0
Offline

Offline

Posts: 82

	Re: Problem: Boost is pulsing « Reply #5 on: October 05, 2020, 12:05:22 AM »

Yes because my Turbos has 0,5bar basespring pressure.

I read this chapter in S4 Wiki many times, because at the beginning I had issues with Throttleplate flapping on less than 0,5 bar.
I divided my new Wastegate pressure value by the old one so I got 1.5/1.3 and then I created a new table in the XDF for the X axis of KFVPDKSD and KFVPDKSE and multiplied the values by 0.15.


	Logged

MetalForLive

Full Member

Karma: +0/-0
Offline

Offline

Posts: 82

	Re: Problem: Boost is pulsing « Reply #6 on: October 07, 2020, 03:45:55 AM »

I think I will try to increase DIMX


	Logged

prj

Hero Member

Karma: +922/-429
Offline

Offline

Posts: 5862

	Re: Problem: Boost is pulsing « Reply #7 on: October 07, 2020, 09:10:35 AM »

Read the boost PID tuning thread.
Or turn off the boost pid totally. Set CWMDAPP to 8 and set fixed duty via KFLDRAPP.

There is nothing to "tune" in KFLDRL or KFLDIMX. These maps are generated from measurements taken.
Until you understand that, better turn the boost pid off.


	Logged

PM's will not be answered, so don't even try.
Log your car properly.

MetalForLive

Full Member

Karma: +0/-0
Offline

Offline

Posts: 82

	Re: Problem: Boost is pulsing « Reply #8 on: October 07, 2020, 09:43:51 AM »

I will read PID section again.


	Logged

MetalForLive

Full Member

Karma: +0/-0
Offline

Offline

Posts: 82

	Re: Problem: Boost is pulsing « Reply #9 on: October 08, 2020, 09:30:53 AM »

With fixed Duty cycle everything is fine.

I think I have completely start over with PID :/


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

May 23, 2024, 10:50:09 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search