Hi, Looking for help with a pinout for a bench setup im building (Audi RB8 Cluster). B5S4 seems pretty well mapped out - http://nefariousmotorsports.com/forum/index.php?topic=3205.0title=

But what im looking for is the RB8 Pinout.

What i have so far is just the Power and ground which works on my bench - https://www.programmersought.com/article/79631630035/

what i dont know is were Kline or CAN wires are  "if they are needed as well". 
Dash Part Number is 8e0920982C

I can do a full writeup with pictures when done. If someone wants to PM me the information or share it here that would be great.

Hope this helps.

Pin assignment at multi-pin connectors on instrument cluster
    
32-pin multi-pin connector, blue
1 -    Washer fluid low
2 -    Coolant level low
3 -    Fuel gauge sender
4 -    Coolant temperature
5 -    Control group 2 Navigation system
6 -    Control group 3 Navigation system
7 -    Control group x Telematics
8 -    Menu switch
9 -    Vacant
10 -    Bonnet switch
11 -    Fuel gauge sender 2
12 -    Menu switch (Out A)
13 -    Vacant
14 -    Vacant
15 -    Vacant
16 -    FDR/TCS (= ESP)
17 -    Convenience CAN High
18 -    Convenience CAN Low
19 -    Infotainment CAN Low
20 -    Infotainment CAN High
21 -    Ambient temp. (input)
22 -    S contact
23 -    Oil level / oil temperature
24 -    Self-levelling suspension
25 -    Menu switch (enter)
26 -    Vacant
27 -    Vacant
28 -    Menu switch (Out B)
29 -    Vacant
30 -    Transponder 2
31 -    Transponder 1
32 -    Terminal 31 (sensor)
    A90-0159
32-pin multi-pin connector, green
1 -    Terminal 58d
2 -    Terminal 30
3 -    Terminal 15
4 -    Vacant
5 -    Speedometer (input)
6 -    Speedometer (output 2)
7 -    Airbag (inverted)
8 -    Turn signal (right-side)
9 -    Brake fluid low
10 -    Turn signal (left-side)
11 -    Turn signal (trailer)
12 -    CAN drive Low
13 -    CAN drive High
14 -    Terminal 61/charge warning
15 -    Vacant
16 -    Oil pressure 2
17 -    Terminal 58s
18 -    Terminal 31 load
19 -    Terminal 31 load
20 -    Vacant
21 -    Speedometer (output 1)
22 -    ABS warning
23 -    K wire
24 -    CAN drive (display)
25 -    Tank flap switch
26 -    CAN diagnosis Low
27 -    CAN diagnosis (display)
28 -    CAN diagnosis High
29 -    HRC (headlight range control)
30 -    Belt buckle
31 -    External buzzer
32 -    Brake pad wear
    A90-0160

I don't know is it against forum rules, but if you ever need, you can find for any other model on this page 

In a strange episode of parallel lives - I wired up an RB4 cluster from B6S4 on the bench for first time last weekend using same power, ground and K wire posted here on the green plug. I was able to extract the EEPROM contents etc.

One thing that perplexes me is that the RB4 is clearly CAN gateway on the B6 platform for the various CAN interfaces on the car. The RB4 presents CAN diagnostics pins according to the factory pinout info but those pins are not actually used on the OBD plug.

Anybody know if / when the OBD diagnosis pins get used on the RB4 cluster - just for something in the factory maybe ?

I used the Kline on both cluster types with no issues. the RB8 needs the Crypto 2004+ to read it correctly... but other then that it was pretty easy to clone and move the dash from one car to the other.

Yep it's just weird to me they could have extended the CAN gateway function in the cluster with CAN diagnosis bus from there to the OBD plug. Only mention of the CAN diagnosis pins is in the elsawin pinout info for the cluster - it's not shown on B6 wiring.