Andrej1701
Jr. Member
Karma: +0/-7
 Offline
Posts: 32
|
 |
« Reply #30 on: March 11, 2021, 03:23:12 AM »
|
|
|
And its curious that yesterday when everything was okay, nefmotor could find a device either..
Is the reason behind that ,that i didnt activatet the dump mode in vcds?
|
|
|
|
|
Logged
|
|
|
|
|
|
Andrej1701
Jr. Member
Karma: +0/-7
Offline
Posts: 32
|
|
« Reply #32 on: March 11, 2021, 03:40:58 AM »
|
|
|
okay short update:
my friend has an kkl cable which i plugged in and boom!
nefmotor found an device but the flashing failed at first and then succeded.. im scared to do something.
I flashed without an memory layout and only with the bin file. is that right ?
although i set the BAUD to 38400... how can i see if something went wrong?
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #33 on: March 11, 2021, 03:45:59 AM »
|
|
|
You have to specific a memory layout.
Flashing random files you find on the internet is bad and this is exactly why. Get your ECU part number and flash that exact file back on and only edit that file going forward. A VCDS cable never works for me, I always use KKL.
|
|
|
|
|
Logged
|
|
|
|
|
Sandstorm3k
|
|
« Reply #34 on: March 11, 2021, 03:56:00 AM »
|
|
|
okay short update:
my friend has an kkl cable which i plugged in and boom!
nefmotor found an device but the flashing failed at first and then succeded.. im scared to do something.
I flashed without an memory layout and only with the bin file. is that right ?
although i set the BAUD to 38400... how can i see if something went wrong?
Sweet, that does sound right to my knowledge. EDIT: You must indeed set correct memory layout i misread that part in your post Flashing random files you find on the internet is bad and this is exactly why. Get your ECU part number and flash that exact file back on and only edit that file going forward.
I 100% agree with this! Read fr, s4wiki and do it properly. |
|
|
|
« Last Edit: March 11, 2021, 04:29:05 AM by Sandstorm3k »
|
Logged
|
|
|
|
fknbrkn
Hero Member
Karma: +185/-23
Offline
Posts: 1454
mk4 1.8T AUM
|
|
« Reply #35 on: March 11, 2021, 04:26:10 AM »
|
|
|
You cannot flash anything without choosing memlayout
Its literally impossible with nef
Idk you absolutely has no idea what are you doing just a random stuff without sharing any details
post your original ecu hw sw
try to connect with vcds. if its ok and ecu responds - flash it with original file
if not - run bootmode on a bench with galletto or chiploader app
|
|
|
|
|
Logged
|
|
|
|
Andrej1701
Jr. Member
Karma: +0/-7
Offline
Posts: 32
|
|
« Reply #36 on: March 11, 2021, 08:32:01 AM »
|
|
|
So installed the HJ File that you gave me and i tried to get thr engine started.
Its just cranking and wont start.
Now i tried to flash the AUM that you guys give me at first but now after i flashed and tried it ,It wont even flash other bin files.
Im depressed right now and i think that i need to boot my ecu or wdy think?
|
|
|
|
|
Logged
|
|
|
|
|
_nameless
|
|
« Reply #37 on: March 11, 2021, 09:00:19 AM »
|
|
|
Discconect the battery for 10 minutes.
-Plug battery back
-turn the inginition ON
-Flash stock ori map
-Turn ignition OFF
-Turn ignition ON
-Start car
BDW: if both files are 1Mb, crosh flash schould work without problems. Traverse engines most off them are croshflasheble
eeprom differences some are not cross flashable without the proper eeprom. example 032hn v001 and 032hn v002. if you cross flash those it will brick after a few key cycles |
|
|
|
|
Logged
|
Giving your mom a tuneup
|
|
|
|
_nameless
|
|
« Reply #38 on: March 11, 2021, 09:03:30 AM »
|
|
|
Depending on location immo 2 euro pre 2001 immo3 2001 on the US is mainly immo 2 upto 2003
this is incorrect. AWW engine code was the only a chassis 1.8t that was immo2 02-05 was immo 3 (awp engine code) the 2001 180 model 1.8t was a awp too and that was immo 3. Info gathered from personal experience |
|
|
|
|
Logged
|
Giving your mom a tuneup
|
|
|
|
_nameless
|
|
« Reply #39 on: March 11, 2021, 09:04:59 AM »
|
|
|
this is incorrect. AWW engine code was the only a chassis 1.8t in the usa that was immo2 02-05 was immo 3 (awp engine code) the 2001 180 model 1.8t was a awp too and that was immo 3. Info gathered from personal experience
|
|
|
|
|
Logged
|
Giving your mom a tuneup
|
|
|
Andrej1701
Jr. Member
Karma: +0/-7
Offline
Posts: 32
|
|
« Reply #40 on: March 11, 2021, 10:03:37 AM »
|
|
|
Can i use for booting my ecu my kkl cable which i used for flashing too ?
Or do i NEED to purchase the Galetto cable?
Lg
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #41 on: March 11, 2021, 12:41:48 PM »
|
|
|
So installed the HJ File that you gave me and i tried to get thr engine started.
Because the file does not match the EEP. Like I said, flash the file that belongs on the ECU, not files people tell you 'might' work. |
|
|
|
|
Logged
|
|
|
|
Andrej1701
Jr. Member
Karma: +0/-7
Offline
Posts: 32
|
|
« Reply #42 on: March 11, 2021, 11:55:31 PM »
|
|
|
Sounds right ,
How can i check if the bin file is fitting for my ecu ?
I mean which parameters do i need to compare for and where can i get them?
|
|
|
|
|
Logged
|
|
|
|
|
Sandstorm3k
|
|
« Reply #43 on: March 12, 2021, 12:36:23 AM »
|
|
|
Sounds right ,
How can i check if the bin file is fitting for my ecu ?
I mean which parameters do i need to compare for and where can i get them?
It literally says on the ECU, that's to my knowledge the only way to be 100% certain. It'll have a number such as 06A906032(xx) and a software version underneath that number such as 0001, 0002, 0003. Find that file, flash it onto your car and it should be back to normal. |
|
|
|
|
Logged
|
|
|
|
Andrej1701
Jr. Member
Karma: +0/-7
Offline
Posts: 32
|
|
« Reply #44 on: March 12, 2021, 12:49:56 AM »
|
|
|
My number is : 60A 906 0 32 HJ
Benzin ME 7.5 0002
I cant flash my ecu because of the issue: immobilizer not authenticated
Why is that so?
|
|
|
|
|
Logged
|
|
|
|
|
