Pages: 1 [2]
Author Topic: 0261208244 4B0906018DN 0004 Definition request please  (Read 5904 times)
_nameless
Hero Member
*****

Karma: +320/-445
Offline Offline

Posts: 2654



« Reply #15 on: September 24, 2022, 07:09:08 AM »

I have the full a2l and hex for the 518f and 518al(ak) but it doesn't matter.  If you have any definition for the later models you can just use that by shifting a few bits.
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
vengines
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #16 on: September 24, 2022, 10:40:33 AM »

I have the full a2l and hex for the 518f and 518al(ak) but it doesn't matter.  If you have any definition for the later models you can just use that by shifting a few bits.
I would be very interested in those definitions and again thanks for all the info


Sent from my iPhone using Tapatalk
Logged
vengines
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #17 on: September 27, 2022, 04:21:56 PM »

Looking for some additional help is there a possibility that the passat 018DN is using the config2 for ESKONF i did a cat sai delete following the wiki and double checked my values and if i pull the sai relay i get a code for it

17841 - Secondary Air Pump Relay (J299)
               P1433 - 004 Open Circuit

All signs point to the rear o2 part working the rear o2 reads 0.00v and says test ok i have yet to unplug it and confirm that way.

I set ESKONF confg 1 to -  AA FF 00 F0 FF FB 3C  - and left config 2 alone
ESKONF config 2 does show a brake booster pump as installed and my car has one.  AA FF 00 30 3F F8 30

i left CDSLS alone
CWKONABG is 0  as part of 02 delete

MSLUB zeroed out across all
MSLBAS 0

also didn't touch FHOKH

Thanks
Logged
gremlin
Hero Member
*****

Karma: +179/-7
Offline Offline

Posts: 568


« Reply #18 on: September 28, 2022, 01:32:11 AM »

ESKONF 1 - used if vechicle with MT
ESKONF 2 - used if vechicle with AT
Logged
vengines
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #19 on: September 28, 2022, 05:57:29 AM »

ESKONF 1 - used if vechicle with MT
ESKONF 2 - used if vechicle with AT


thank you this completely makes sense to my results then
Logged
vengines
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #20 on: October 02, 2022, 03:11:26 PM »

hey guys i'm working on the readiness monitors now just for completeness and cant get the SAI or O2 to set passed
this is log from vcds

i have SRYLS and SRYSLS set to 0 have tried ORI and 0
and have tried to set readiness in VCDS the test never goes through for B1S1 age test and sai test never goes to ok 300s + run time for each

MSLUB 0 across the table
MSLBAS 0

Any Direction appreciated if you need any more info i will give what i can im fine with not installed or passed just want to avoid failed
thanks
--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Readiness Status: 0010 1000
Exhaust Gas Recirculation: Passed
Oxygen Sensor Heating: Passed
Oxygen Sensor(s): Failed or Incomplete
Air Conditioning: Passed
Secondary Air Injection: Failed or Incomplete
Evaporative Emissions: Passed
Catalyst Heating: Passed
Catalytic Converter(s): Passed


Sunday,02,October,2022,17:40:06:40722
VCDS -- Windows Based VAG/VAS Emulator Running on Windows 10 x64
VCDS Version: 22.9.0.0 (x64)  HEX-V2 CB: 0.4623.4
Data version: 20220830 DS341.0
www.Ross-Tech.com




--------------------------------------------------------------------------------
--------------------------------------------------------------------------------


Mode 01 - PID 01 : Readiness  --  Address 10

Number of DTCs stored: 0  --  MIL Status: MIL OFF
Misfire monitoring:  Passed
Fuel System:  Passed
Comprehensive Components:  Passed
Catalyst monitoring: Not installed.
Heated catalyst monitoring: Not installed.
Evaporative system monitoring:  Passed
Secondary air system monitoring:  Failed or Incomplete
A/C system refrigerant monitoring: Not installed.
Oxygen sensor monitoring:  Failed or Incomplete
Oxygen sensor heater monitoring: Not installed.
Exhaust Gas Recirculation: Not installed.
Logged
Pages: 1 [2]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.026 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)