NefMoto > Noob Zone > Noob Questions (Moderator: turboat) > noob Project stage 1 1.8t
Pages: 1 [2]
« previous next »
Author Topic: noob Project stage 1 1.8t  (Read 6159 times)
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85
« Reply #15 on: November 14, 2022, 09:14:41 AM »
Quote from: JeanAwt on November 14, 2022, 06:10:43 AM
hi,I ordered a spare ecu. how do you read the eprom ecu? I understood that it is necessary to be in bootmode (pin 24 to the mass or by obd which software?) for the moment I manage to read the eprom cluster with vag commander. I equipped myself with me7eeprom me7_95040
but I am far from having read everything and understood everything. I have plenty to do


sorry for my google translate

correct, put ecu in bootmode (solder or wire to chip pin->gnd) and then connect with me7eeprom program (works with ft232rl cable).
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #16 on: November 14, 2022, 09:28:13 AM »
ok thank you. for a "switchable" version a switch outside the ecu? I read 10seconds to ground with contact on. does this erase the flash? no other solution to clone? me7eprom works in cmd too?
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #17 on: November 14, 2022, 09:38:14 AM »
I'm going to wait to receive the backup ecu. No risk of immo blocking if I swap my stock/backup ecu and put the stock back on afterwards to read and check the software number and watch the flash.
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85
« Reply #18 on: November 14, 2022, 10:14:48 AM »
Quote from: JeanAwt on November 14, 2022, 09:28:13 AM
ok thank you. for a "switchable" version a switch outside the ecu? I read 10seconds to ground with contact on. does this erase the flash? no other solution to clone? me7eprom works in cmd too?

I brought both the gnd and bootmode wire outside the ecu. I didn't put a switch but I plugged the wire ends and when I need boot mode, I remove the plugs and connect the wires together.

bootmode is not needed for binary read, but eeprom read it is needed as far as i know. Does not erase flash.

Me7eprom works in windows cmd only.
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #19 on: November 14, 2022, 10:35:12 AM »
just tried reading eprom ecu not working by vag commander1.4/2.5 yet there is option with choice of ecu me7.1 7.5...
probably because of the bootmode Huh
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
TeknoFi
Full Member
***

Karma: +1/-3
Offline Offline

Posts: 85
« Reply #20 on: November 14, 2022, 10:51:19 AM »
Quote from: JeanAwt on November 14, 2022, 10:35:12 AM
vag commander

that is tool for instrument cluster, not ecu... you are reading ecu eeprom, not instrument.
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #21 on: November 14, 2022, 11:47:04 AM »
there are the 2 cluster eprom reading it works but not the ecu eprom reading and there is also flash reading/writing
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #22 on: January 02, 2023, 08:48:39 AM »
Hi
I am progressing slowly but surely on my little project. I now have a 2nd ecu that I cloned. I saw that I am missing some maps if someone can help me that would be cool:
TEMIN
FKSTT
FNSSM
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #23 on: January 15, 2023, 12:52:27 AM »
Quote from: Blazius on November 13, 2022, 05:12:32 PM
Same bootrom version and pcb design files can be crossflashed without any issues. Pretty much anything but please dont make me look up all the info.
Post the whole output from me7check of bins..

It looks like that is even the same ecu so one of the softs is newer so tldr you can. Dont forget about your eeprom


is it possible to flash 4B0906018CG on 4B0906018R?
or another?
of course keeping my flash eprom and set ESKONF.
thank you

ME7Check v1.12 (c) mki, 06/2004-05/2012
Checking file 4B0906018R.bin (size=1048576)
Reading Version Strings...
-> Bootrom Version = 05.12
-> EPK = 40/1/ME7.5/5/4016.31//24b/Dst03o/300500//
-> Contents of ECUID data table:
   - '0261206539'         (SSECUHN)
   - '1037354801'         (SSECUSN)
   - '4B0906018R  '       (VAG part number)
   - '0003'               (VAG sw number)
   - '1.8L R4/5VT     '   (engine id)
-> Contents of ECUID data table:
   - 'HW_MAN004'

-> No errors found. File is OK.

ME7Check v1.12 (c) mki, 06/2004-05/2012
Checking file Audi-A4-1,8T-AWT-4B0906018CG-0261207215-360306saiOFF.bin (size=104
8576)
Reading Version Strings...
-> Bootrom Version = 05.12
-> EPK = 40/1/ME7.5/5/4016.31//24b/Dst02o/290900//
-> Contents of ECUID data table:
   - '0261207215'         (SSECUHN)
   - '1037360306'         (SSECUSN)
   - '4B0906018CG '       (VAG part number)
   - '0002'               (VAG sw number)
   - '1.8L R4/5VT     '   (engine id)
-> Contents of ECUID data table:
   - 'HW_MAN004'

-> No errors found. File is OK.   *********************
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
fknbrkn
Hero Member
*****

Karma: +186/-24
Offline Offline

Posts: 1456


mk4 1.8T AUM
« Reply #24 on: January 15, 2023, 01:04:41 AM »
Why you just didnt try that? 10mins deal if you have bootmode in case od a failure
Logged
mdz
Full Member
***

Karma: +12/-1
Offline Offline

Posts: 73
« Reply #25 on: January 15, 2023, 01:52:56 AM »
There's fully defined 018CA floating around here.
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #26 on: January 15, 2023, 03:20:21 AM »
I tried 018CG does not start, I want to know why? 018r is in a4 b5 2000/018CG a4 b5 2001 . same engine. a quattro file will prevent it from starting on traction? different EPK numbers?

yes I can try all the files that are close to 018R and tell you which ones work. but I would like to understand what makes it not work software?hardware numbers? the file?

 indeed there is a map pack 018CA on the forum and the CA file seems to correspond to 018R.

he wrote:
"Have fun guys, the 018CA.bin file works great on the 018CG ecu too. I use it myself.

-> Bootrom Version = 05.12
->EPK=42/1/ME7.5/331/4518.10//24b/Dst03o/300500/
-> Contents of ECUID data table:
   - '0261206917' (SECECUHN)
   - '0000000000' (SSECUSN)
   - '4B0906018CA' (VAG part number)
   - 'X003' (VAG sw number)
   - 'X24b803o.hex' (engine id)
-> Contents of ECUID data table:
   - 'HW_MAN004'   

            Dst03o/300500 as 018R
« Last Edit: January 15, 2023, 05:11:36 AM by JeanAwt » Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #27 on: January 16, 2023, 02:08:07 PM »
018CA engine starts Cool
Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425
« Reply #28 on: January 16, 2023, 04:11:21 PM »
Quote from: JeanAwt on January 15, 2023, 03:20:21 AM
I tried 018CG does not start, I want to know why?

I assume the internal ROM is different.
Logged
JeanAwt
Full Member
***

Karma: +10/-12
Offline Offline

Posts: 242
« Reply #29 on: January 18, 2023, 01:36:52 PM »
I wonder if my LAMFA 1CED9 axis addresses are correct. rpm ok factor 0.007813 but load % 1CECD factor: 0.003052.
 I have 160/03/40/80/120. how to restore order? in 6x15 50/60/70/80/90/97.5?
I have to set LAMFA_COLAXIS
LAMFA_ROWAXIS? thank
« Last Edit: January 25, 2023, 11:04:53 AM by JeanAwt » Logged
A4 B5 avant 1.8T 2000 NO QUATTRO
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 29, 2024, 06:26:24 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.043 seconds with 18 queries. (Pretty URLs adds 0.005s, 0q)