ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD!

Pages: [1]

« previous next »

Author

Topic: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! (Read 6185 times)

R32Dude

Full Member

Karma: +45/-10
Offline

Offline

Posts: 248

	ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « on: April 25, 2023, 01:00:27 AM »

ST10 ME7.1.1 Ripper
-------------------
Allows the three important ROMs to be extracted without the need to remove ECU from car. These can be used for studying with Ida, winols etc. They can also be used to clone a similar family ECU on the bench with other tools such as MPPS .

Main Features:

Easily extract Flash, mpc and eeprom in a few minutes from OBD port.

Flash takes 4-5 mins, mpc 3-4 mins and eeprom 1 min (after extracting flash first)

NO need to remove ECU from the car!!
-------------------------------------

Only works on ST10F ME7.1.1, haven't tried other ME7.X.X

Will NOT work on C167 based ECUs including ST10C167!

Personally tested on 2.5 Beetle 07K906032Q & Mk5 R32 022906032KG,CE

Requirements: KKL cable with COM port drivers - in your COM port settings, advanced, change latency to 2 instead of 16.
ECU must have KLine connection to OBD port.

Intallation: Portable, simply extract whole folder and run. Don't run from USB. Change COM port from 3 to yours.

If it works for you give me a +, if you get error messages take a screenshot, I might be able to help.
The code is quite flexible, but I don't have any code for ST10s other than 7.1.1 so it may not work for other variants.
Remember though, 7.1.1 on C167/ST10C167 won't work.

It might be able to backup tuned ECUs too, if they didn't play with KWP services.

Have fun.


« Last Edit: November 14, 2023, 06:04:02 AM by R32Dude »	Logged

nyet

Administrator
Hero Member

Karma: +607/-168
Offline

Offline

Posts: 12268

	Re: ST10 RIPPER Easy backup of ME7.1.1 on OBD « Reply #1 on: April 25, 2023, 02:59:25 PM »

github repo?


	Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex

Mangusta

Newbie

Karma: +1/-0
Offline

Offline

Posts: 2

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #2 on: June 24, 2023, 12:34:38 AM »

Worked very well for me first time. I finally managed to get my ecu cloned by a friend. He is quite knowledgeable, 10 years, and told me I had to remove the ecu from the car. Thanks to this there was no need. I could never find something that could get all three sections easily.
Thank you for sharing sir.


	Logged

EuroXs4

Full Member

Karma: +15/-31
Offline

Offline

Posts: 209

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #3 on: October 06, 2023, 05:30:59 PM »

Is there a way to get this to work with C167 processor?


	Logged

Geomeo

Full Member

Karma: +11/-6
Offline

Offline

Posts: 152

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #4 on: October 06, 2023, 05:37:07 PM »

Quote from: EuroXs4 on October 06, 2023, 05:30:59 PM

Is there a way to get this to work with C167 processor?

Now I could be wrong here, but since OP's first post says the following:

"Will NOT work on C167 based ECUs"

And then
"remember though, 7.1.1 on C167 won't work."

Probably not.

Grin


	Logged

nyet

Administrator
Hero Member

Karma: +607/-168
Offline

Offline

Posts: 12268

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #5 on: October 06, 2023, 10:32:29 PM »

Quote from: EuroXs4 on October 06, 2023, 05:30:59 PM

Is there a way to get this to work with C167 processor?

The nefmoto flasher?


	Logged

unicorn89

Newbie

Karma: +0/-0
Offline

Offline

Posts: 18

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #6 on: June 25, 2024, 04:37:31 AM »

Not working...

Code:

Opening Port 3...
 
Port:  Open
 
Setting BAUD to 10400
 
SLOW INIT Started
Waiting 4s...
Sending 5 BAUD signal...
 
-------------------------
Expecting 3 bytes:
55, KB1, KB2 
 
Got Them! : 55, 1, 8A, 
Now Sending inverted KB2:75
 
Expecting Echo & Inverted address...
Received Both
------------------------
 
Connected to ECU 
---------------- 
 
ECU info:
Error message not received on time
Trying Fast Connection..
  Asking For Seed 3\4
Error message not received on time
Error:FastBaud-No Response
Backing up will take longer than 4 minutes!


	Logged

Matthewest91

Full Member

Karma: +0/-0
Offline

Offline

Posts: 105

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #7 on: August 09, 2024, 10:18:15 AM »

Wondering if I did something wrong. Does not look like the st10 ripper is getting any feedback.

Sent from my iPhone using Tapatalk


	Logged

gremlin

Hero Member

Karma: +196/-9
Online

Online

Posts: 653

	Re: ST10 RIPPER Easy,Complete backup of ME7.1.1 on OBD! « Reply #8 on: August 09, 2024, 12:45:37 PM »

Quote from: Matthewest91 on August 09, 2024, 10:18:15 AM

Wondering if I did something wrong. Does not look like the st10 ripper is getting any feedback.

Don't waste your time with st10ripper - it only works with KWP2000 over ISO9141 ecus.
Just saw in your messages above - your ecu has SW: 8E2910560B and HW:8E2907560.

Protocols supported by this hardware:

KD-Diagnose TP2.0/KWP2000
OBD−Diagnose ISO−Can (OBD on Can)
TP2.0 firmware programming.

It's no wonder you can't connect using the tools you have.


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

November 22, 2024, 03:44:42 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search