Pages: [1] 2 3
Author Topic: Removing EGt sensor from K04-023 -> MIL?  (Read 24199 times)
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409



« on: September 13, 2012, 05:49:16 AM »

Hello

I understand that removing the egt probe from k04-023 turbocharger will cause mixture enrichment and probably MIL.
Is there a way to remove it without affecting car work behavior from SW side?

Thank you.
Logged

Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
Aragorn
Full Member
***

Karma: +3/-0
Offline Offline

Posts: 94


« Reply #1 on: September 13, 2012, 08:11:30 AM »

i believe you need to set CATR = 0
Logged
phila_dot
Hero Member
*****

Karma: +170/-11
Offline Offline

Posts: 1709


« Reply #2 on: September 13, 2012, 08:21:17 AM »

S4wiki

http://s4wiki.com/wiki/Tuning#EGT
Logged
nokiafix
Full Member
***

Karma: +19/-2
Offline Offline

Posts: 124


« Reply #3 on: September 13, 2012, 09:48:45 AM »

With a k034-023 on a stock manifold I would want to run the EGT in place.

NIck
Logged
nokiafix
Full Member
***

Karma: +19/-2
Offline Offline

Posts: 124


« Reply #4 on: September 13, 2012, 09:50:43 AM »

You could run 032HJ SW non EGT and utilse the egt model
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903


« Reply #5 on: September 13, 2012, 10:21:52 AM »

But as stated Catr needs to be set to 0 otherwise you get constant protection fuelling ( ie 0.75 all the time) Setting it 0 gives normal lambda fuelling as found in the Hn or Hj.

I have asked for s4wiki to be updated
Logged
phila_dot
Hero Member
*****

Karma: +170/-11
Offline Offline

Posts: 1709


« Reply #6 on: September 13, 2012, 10:35:39 AM »

But as stated Catr needs to be set to 0 otherwise you get constant protection fuelling ( ie 0.75 all the time) Setting it 0 gives normal lambda fuelling as found in the Hn or Hj.

I have asked for s4wiki to be updated

Ahh...ok, I guess that negates the need to FF TABGSS?

TABGSS was being FF'ed because when the sensor is unplugged it gives a max reading causing intervention.
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903


« Reply #7 on: September 13, 2012, 10:55:58 AM »

Yes that would make sense, I never tried FF tabgss as when I got the issue I had a look through FR and stumbled on CATR and that worked so left it at that. As far as I can tell just setting Catr to 0 switches the EGT off com
Logged
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903


« Reply #8 on: September 13, 2012, 10:59:06 AM »

Yes that would make sense, I never tried FF tabgss as when I got the issue I had a look through FR and stumbled on CATR and that worked so left it at that. As far as I can tell just setting Catr to 0 switches the EGT off completely.

It works well if you want to run a BAM flash on a 032hn or hj ecu and don't obviously have EGT. In my case it's been hybrid k03's as the flash already has s3 maf scaling s3 fuelling etc etc
Logged
phila_dot
Hero Member
*****

Karma: +170/-11
Offline Offline

Posts: 1709


« Reply #9 on: September 13, 2012, 11:02:51 AM »

Yes that would make sense, I never tried FF tabgss as when I got the issue I had a look through FR and stumbled on CATR and that worked so left it at that. As far as I can tell just setting Catr to 0 switches the EGT off com

CATR shuts down ATR I'm guessing. So CDATR and CDATS are still required to shut down diagnosis?

I'm not at my computer and have never cared for EGT delete, otherwise I would just look myself.
Logged
professor
Sr. Member
****

Karma: +25/-0
Offline Offline

Posts: 409



« Reply #10 on: September 19, 2012, 10:50:49 AM »

CATR, CDATR and CDATS did the job.

Thanks guys  Smiley
Logged

Seat Ibiza MK4 Cupra 1.8t 20V, stg3.
"Those 1.8T 20V machines are really tough" ©
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #11 on: September 19, 2012, 12:38:11 PM »

But as stated Catr needs to be set to 0 otherwise you get constant protection fuelling ( ie 0.75 all the time) Setting it 0 gives normal lambda fuelling as found in the Hn or Hj.

I have asked for s4wiki to be updated

I didn't see this. Can somebody clarify what, exactly, should be added to the wiki?

In particular, i didn't modify CATR and i dont see lambda problems (with EGTs installed)... unless im missing something... is it only needed if you remove EGT sensors entirely?

Thanks.
« Last Edit: September 19, 2012, 12:44:13 PM by nyet » Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
littco
Hero Member
*****

Karma: +52/-7
Offline Offline

Posts: 903


« Reply #12 on: September 19, 2012, 02:15:00 PM »

Yes to completely remove EgT and not set off egt protection fuelling CATR needs to be set to 0 . If you remove the EGT but leave at 1 you'll get a constant .75
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #13 on: September 19, 2012, 02:22:09 PM »

Thanks. s4wiki updated.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
sonique
Sr. Member
****

Karma: +24/-12
Offline Offline

Posts: 282


« Reply #14 on: May 28, 2015, 05:44:31 PM »

and after removing EGT
not need CWLAMBTS  set 4 ?
because example :AUQ 180PS original file "4"
BTS fueling working fine CWLAMBTS  0 ?
Logged
Pages: [1] 2 3
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.023 seconds with 17 queries. (Pretty URLs adds 0s, 0q)