Dev Blog
Forum
Wiki
About
NefMoto
>
Technical
>
NefMoto Software
>
Newbie help!
Pages: [
1
]
« previous
next »
Author
Topic: Newbie help! (Read 7377 times)
christtnorwich
Newbie
Karma: +0/-0
Offline
Posts: 13
Newbie help!
« on: October 07, 2012, 11:16:54 AM »
Hi everyone, this forum is ace! But I have a few questions, I have a Audi tt 225 which has a bad remap done by the old owner, my mission is to revert the ecu to stock, I have a cable and the software from this site but can't seem to make a connection to my ecu, maybe is using the software wrong, should it auto connect of do I need to load my ecu file? or the map maybe locked by the mapper?
Any help with getting my mission completed would be really appreciated
When I plug in and open the programme nothing happens?
Many thanks
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Newbie help!
« Reply #1 on: October 07, 2012, 11:51:18 AM »
You have to select a few options before connecting. At the top you select the communication protocol, baud rate (mine is set to 124800), and with your cable connected select it from the device list. You may have to hit "refresh devices" to see it. After that, select "slow init" from the desired connection speed toolbar, and hit connect (I suppose if you bought the premium features you could select "fast init".
That should get you connected. If you're used to running scanning software, these options are relatively standard. Good luck, I'm a newbie myself. I did a lot of reading before posting anything, mainly because people on this forum appear to be very proud of their work, and will not expend any effort for those who do not make an honest attempt before asking for help. Good luck!
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
christtnorwich
Newbie
Karma: +0/-0
Offline
Posts: 13
Re: Newbie help!
« Reply #2 on: October 07, 2012, 12:21:43 PM »
Thanks so much for your help
I use vag com and have a blue eBay cable, my cable won't appear in the device list! Should I pull the dashpod fuse?
Chris
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Newbie help!
« Reply #3 on: October 07, 2012, 01:13:17 PM »
Does the cable connect using vcds? If it does, what com port is it on? Sounds like you either need to reinstall the drivers, or change the com to a lower port in control panel. I know many programs will only look for an interface in ports 1-4. Mine is set at 2. FWIW, I have the all blue ebay cable, and the blue with silver cord.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
christtnorwich
Newbie
Karma: +0/-0
Offline
Posts: 13
Re: Newbie help!
« Reply #4 on: October 07, 2012, 02:14:39 PM »
Yeah it connects with vcds easily, think and is connected to com port 3 I will have a play tomorrow
your help is muchly appreciated
Logged
madswp
Full Member
Karma: +3/-0
Offline
Posts: 102
Re: Newbie help!
« Reply #5 on: October 08, 2012, 01:42:57 PM »
i also fist bought a random blue ebay vagcom cable. it didnt support the ftdi driver. i suppose you have to make sure your cable has the FT232RL chip inside. not all blue ebay cables have that.
here's a link to the one i bought and it works perfectly:
http://www.ebay.co.uk/itm/290749432731?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649#ht_1588wt_1298
Logged
ddillenger
Hero Member
Karma: +641/-21
Offline
Posts: 5640
Re: Newbie help!
« Reply #6 on: October 08, 2012, 02:11:44 PM »
Quote from: madswp on October 08, 2012, 01:42:57 PM
i also fist bought a random blue ebay vagcom cable. it didnt support the ftdi driver. i suppose you have to make sure your cable has the FT232RL chip inside. not all blue ebay cables have that.
here's a link to the one i bought and it works perfectly:
http://www.ebay.co.uk/itm/290749432731?ssPageName=STRK:MEWNX:IT&_trksid=p3984.m1439.l2649#ht_1588wt_1298
That's one of the cables I have, I paid .01 for it, with 3.99 shipping.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
Pages: [
1
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
November 23, 2024, 01:55:24 AM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...
