NefMoto > Technical > Tuning > Documents & Helpers & How To's > The 5120 hack - Running up to 5bar absolute pressure on ME7.x
Pages: 1 ... 7 8 [9] 10 11 ... 37
« previous next »
Author Topic: The 5120 hack - Running up to 5bar absolute pressure on ME7.x  (Read 329254 times)
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #120 on: February 06, 2013, 10:52:19 AM »
Quote from: prj on February 04, 2013, 12:50:05 PM
No. You just use a valve that is big enough, and these issues do not happen.

It's really the basics. You can disagree all you want, fact is that you need a stronger spring to keep it shut on idle or suck in unfiltered air.
Stronger spring - does not open soon enough when it should be.

Less efficiency, harder on the turbo, and makes MAF readings go all over the place. You should have the N249 actuating your BOV, instead of removing it.

I'll hook the N249 up for a test just for you ;-)
Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #121 on: February 06, 2013, 10:53:03 AM »
Quote from: mightemouce on February 06, 2013, 08:12:48 AM
Any Updates on this for M-Box?

I'm planning on posting a stock M Box modified and the xdf tonight.
Logged
julex
Hero Member
*****

Karma: +79/-4
Offline Offline

Posts: 923
« Reply #122 on: February 06, 2013, 12:09:35 PM »
splendid!

I am already sick of tuning my car on fixed KFLDRL... Do I put high enough PID limiter to boost up quick and overshoot or keep it low but have "slow spooling" turbos... a conundrum. Having full PSI range in logs will rock too!
Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #123 on: February 06, 2013, 12:13:42 PM »
Quote from: julex on February 06, 2013, 12:09:35 PM
splendid!

I am already sick of tuning my car on fixed KFLDRL... Do I put high enough PID limiter to boost up quick and overshoot or keep it low but have "slow spooling" turbos... a conundrum. Having full PSI range in logs will rock too!

I hear ya there... I was testing the PID control the last few days to make sure it was working right before I posted everything. It seems to be.
Logged
mightemouce
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 67
« Reply #124 on: February 06, 2013, 01:09:37 PM »
Quote from: britishturbo on February 06, 2013, 10:53:03 AM
I'm planning on posting a stock M Box modified and the xdf tonight.

Woohoo can't wait to tinker with my file tonight. Reading through all this again if I leave DSLGRAD and DSLOFS at their regular values and still run a 2.5 bar map sensor until I get a new sensor my logged boost should be half of what it actually is correct?

Any chance I can purchase one of those MPX pressure sensors from you ?
« Last Edit: February 06, 2013, 01:15:56 PM by mightemouce » Logged
phila_dot
Hero Member
*****

Karma: +173/-11
Offline Offline

Posts: 1709
« Reply #125 on: February 06, 2013, 02:16:35 PM »
Quote from: mightemouce on February 06, 2013, 01:09:37 PM
Woohoo can't wait to tinker with my file tonight. Reading through all this again if I leave DSLGRAD and DSLOFS at their regular values and still run a 2.5 bar map sensor until I get a new sensor my logged boost should be half of what it actually is correct?

Any chance I can purchase one of those MPX pressure sensors from you ?

You have to rescale them
Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #126 on: February 06, 2013, 02:18:12 PM »
Quote from: mightemouce on February 06, 2013, 01:09:37 PM
Woohoo can't wait to tinker with my file tonight. Reading through all this again if I leave DSLGRAD and DSLOFS at their regular values and still run a 2.5 bar map sensor until I get a new sensor my logged boost should be half of what it actually is correct?

Any chance I can purchase one of those MPX pressure sensors from you ?

To run the stock 2.5 bar sensor you divide DSLGRAD and DSLOFS by 2.
When I upload files later I'll have an M Box file for the stock 2.5 bar sensor and one for 4 bar sensor.
Logged
marcellus
Sr. Member
****

Karma: +2/-1
Offline Offline

Posts: 472
« Reply #127 on: February 06, 2013, 02:34:03 PM »
Scared and excited.... Grin
Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #128 on: February 06, 2013, 10:49:43 PM »
OK so I took a seconds to convert some M box files over to 5120 support.
Versions should be self explanatory.
XDF files included with all the changes.

This may not be complete, but it works and has been used on my daily driver for over 500 miles now without any problems.

These are based on the 8D0907551M-002 file:

ME7Check v1.12 (c) mki, 06/2004-05/2012
Checking file 8D0907551M-002.bin (size=1048576)
Reading Version Strings...
-> Bootrom Version = embedded in CPU, asume 05.12/05.32
-> EPK = 40/1/ME7.1/5/6005.01//22m/DstC2o/011200//
-> Contents of ECUID data table:
   - '0261207143'         (SSECUHN)
   - '1037360857'         (SSECUSN)
   - '8D0907551M  '       (VAG part number)
   - '0002'               (VAG sw number)
   - '2.7l V6/5VT     '   (engine id)
-> Contents of ECUID data table:
   - 'HW_MAN004'

-> No errors found. File is OK.   *********************

[Editor's note: There are a few minor errors in these files... please read http://nefariousmotorsports.com/forum/index.php?topic=3027.msg63024#msg63024]
« Last Edit: October 01, 2014, 11:24:24 AM by nyet » Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #129 on: February 06, 2013, 10:53:11 PM »
Here's the "nyet" hpa list updated for the 8D0907551M box also for those that might need it.
Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #130 on: February 06, 2013, 10:54:05 PM »
Quote from: marcellus on February 06, 2013, 02:34:03 PM
Scared and excited.... Grin

If you want I can just convert your latest file over to 5120... or just use the xdf...
Logged
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #131 on: February 06, 2013, 11:27:40 PM »
Note:

Logged pressure variables will now be half of their actual value using normal ecu logging.
The easy fix for this is to double the scale factor being used.
For ME7Logger this means the values in the .ecu file.
For example ps_w scale factor gets doubled to 0.078125
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640
« Reply #132 on: February 06, 2013, 11:29:55 PM »
Great work. You went this far, post the .ecu file with the corrections as well.

LOL.
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
britishturbo
Sr. Member
****

Karma: +14/-1
Offline Offline

Posts: 306
« Reply #133 on: February 06, 2013, 11:32:46 PM »
Quote from: ddillenger on February 06, 2013, 11:29:55 PM
Great work. You went this far, post the .ecu file with the corrections as well.

LOL.

You mean this? lol
Logged
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640
« Reply #134 on: February 06, 2013, 11:34:52 PM »
haha

Wait for it. Someone's going to come in and ask for more. It's inevitable.

 Grin
Logged
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
Pages: 1 ... 7 8 [9] 10 11 ... 37
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 10, 2024, 02:43:17 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.024 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)