Pages: [1]
Author Topic: P0602/P1681 on some newer me7.5 ecus(2004 MY)  (Read 33844 times)
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 537


« on: May 23, 2013, 09:54:55 PM »

Ive noticed this lately on two cars, flash goes well, seems stuck in programming mode maybe?

Any solutions? i tried deleting the code out and i still get it(may be stored in eeprom)
« Last Edit: December 27, 2018, 11:45:09 AM by nyet » Logged
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655


« Reply #1 on: May 23, 2013, 10:01:01 PM »

601 is stored on the same 2 lines as immo. right before chksum. maybe 602 is stored there as well.
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #2 on: May 23, 2013, 10:05:50 PM »

When that happens I disconnect, then perform a full read. After that it usually clears itself.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 537


« Reply #3 on: May 24, 2013, 08:53:39 AM »

ive tried the read trick, no luck yet, maybe try reading it a few times until it kicks.

Logged
Gonzo
Sr. Member
****

Karma: +20/-30
Offline Offline

Posts: 483


« Reply #4 on: May 24, 2013, 09:03:49 AM »

Use my patch...
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #5 on: May 24, 2013, 09:05:47 AM »

Use my patch...

Which patch is that?
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
RaraK
Hero Member
*****

Karma: +58/-2
Offline Offline

Posts: 537


« Reply #6 on: May 25, 2013, 09:31:47 AM »

Which patch is that?


its not a patch, its disabling p0602-carb bit in file.  which did not work, which means its likely set in eeprom.

i however cannot reproduce this error on the bench now to see what gets set.

Logged
Gonzo.
Guest
« Reply #7 on: June 22, 2013, 10:09:15 PM »


its not a patch, its disabling p0602-carb bit in file.  which did not work, which means its likely set in eeprom.

i however cannot reproduce this error on the bench now to see what gets set.


Worked for me...

Just flash with MPPS or whatever you have. It will take care of it.
Logged
guentherkapp
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #8 on: January 17, 2015, 12:50:52 PM »

I ran into this recently as well on my 2005 AWP 1.8T Jetta wagon.
It occurred after the initial read of the flash, but I admit I could speculate that this my mistake, in not properly disconnecting after the read, meaning I closed the application (NefMoto flash reader) instead of selecting disconnect before. So there is the potential that the missing disconnect command has caused this, unless the application does this automatically before it closes.
Anyway, the only way I found to overcome it was to reflash with the file I had loaded before. Multiple reads did not help (I did several experiments before).
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #9 on: January 17, 2015, 02:06:13 PM »

We have since developed an ASM workaround for this, it's a sticky somewhere Smiley
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
guentherkapp
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #10 on: January 17, 2015, 02:55:58 PM »

Thanks that is great to know. I am sure I will find it and it also tells me that I did not make a mistake in not disconnecting manually before closing the flash program.
Please allow me to ask (it is just my engineering mind) - do we understand the root cause of this? I assume - yes, since otherwise the ASM (programmatic solution, assuming ASM stands for assembler) might not work in all of the cases.
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #11 on: January 17, 2015, 04:10:43 PM »

The issue is that nefmoto doesn't properly exit the programming session on these newer ecus. It was designed to work with an earlier generation of me7 that didn't contain this code.

Most professional tools don't have the issue.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
guentherkapp
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 13


« Reply #12 on: January 18, 2015, 03:03:58 PM »

If I could find the details on what needs to change (meaning assuming there is a way to detect to newer versions of the ECU and it is known what commands need to be added or remove), I probably could modify the source code and update the NefMoto tool.
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #13 on: January 18, 2015, 04:28:29 PM »

If I could find the details on what needs to change (meaning assuming there is a way to detect to newer versions of the ECU and it is known what commands need to be added or remove), I probably could modify the source code and update the NefMoto tool.

Nefmoto is closed source!
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #14 on: December 27, 2018, 11:46:19 AM »

http://nefariousmotorsports.com/forum/index.php?topic=6719.0title=
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.029 seconds with 17 queries. (Pretty URLs adds 0s, 0q)