NefMoto > Technical > Flashing and Chipping > After flash ECU info is "THIS-IS-THE-RAM-PROGRAM"
Pages: [1]
« previous next »
Author Topic: After flash ECU info is "THIS-IS-THE-RAM-PROGRAM"  (Read 8396 times)
Matt Danger
Full Member
***

Karma: +17/-1
Offline Offline

Posts: 116
« on: March 01, 2011, 09:00:41 PM »
Hi all, forgive me if this is a simple problem. I tried to search around but didn't come up with much.

I've tried flashing a few different files using Tony's software. Some stock, some modified. Slow init with the two rate options. After each flash the ECU info will report "THIS-IS-THE-RAM-PROGRAM". Both with Tony's software and Vag-Com. The car will not start (spare ECU so I'm not stranded).

This post suggests that this will happen when the ECU is still in a programming session. However, Tony's flashing tool completes the flash successfully and I choose to disconnect when I'm done.

This post suggests that this message means the ECU is in a fail safe mode. If this is the case I guess my question is what do I need to do to prevent this problem?

Am I missing something simple? I can flash using Galleto in boot mode but I'd rather use Tony's flasher  Smiley

I've attached the log file, if it can be of any use.
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +132/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3
« Reply #1 on: March 01, 2011, 09:27:48 PM »
THIS-IS-THE-RAM-PROGRAM means the ECU is in programming mode and running out of code loaded into RAM.

Turning the ignition off should cause the ECU to exit programming mode. If the ECU believes the code programmed to the flash is bad, then it won't exit programming mode when the ignition is turned off.

PS: Log files look fine. When you were using version 1.6.1.0 you had some communication errors. Now that you are using version 1.7.0.0 you don't have any communication errors.
« Last Edit: March 01, 2011, 09:31:29 PM by Tony@NefMoto » Logged
Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
msundercober
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 46
« Reply #2 on: March 02, 2011, 02:18:37 PM »
Write it on the bench and try if car starts.
Logged
Bi-turbo
Full Member
***

Karma: +1/-7
Offline Offline

Posts: 164
« Reply #3 on: September 24, 2014, 11:55:33 PM »
Quote from: Tony@NefMoto on March 01, 2011, 09:27:48 PM
THIS-IS-THE-RAM-PROGRAM means the ECU is in programming mode and running out of code loaded into RAM.

Turning the ignition off should cause the ECU to exit programming mode. If the ECU believes the code programmed to the flash is bad, then it won't exit programming mode when the ignition is turned off.

How do you get around getting the ecu to exit the programming?
Logged
flamy
Full Member
***

Karma: +6/-0
Offline Offline

Posts: 56
« Reply #4 on: September 25, 2014, 02:19:39 PM »
Had this also one time after forgotten to turn off ignition after flashing.
Turning it off and on again and ecu was working as expected.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12268


WWW
« Reply #5 on: September 25, 2014, 03:29:45 PM »
Quote from: Bi-turbo on September 24, 2014, 11:55:33 PM
How do you get around getting the ecu to exit the programming?

I can't make head or tail of this question :/
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Bi-turbo
Full Member
***

Karma: +1/-7
Offline Offline

Posts: 164
« Reply #6 on: September 25, 2014, 10:30:46 PM »
This is partly sorted now, the .bin is at fault as the 2 other files I have go on fine
Logged
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1600
« Reply #7 on: July 15, 2019, 11:32:37 PM »
8N0906018 APY ecu comes with soldered 29F400BT

I was able to read it while in the car.
It failed writing at around 40% with "general error" in the car with mpps.
It failed writing at around 40% with "general error" on the bench.
I desoldered one resistor (the one with the red dot) and tried to write different times...
It failed different times in bootmode with "programming error" before 100%.
It failed different times on the bench with "general error" before 100%.
There is no propt to turn ignition off after writing.

Right now ecu is in the ram program. Should i try to write flash outside of the ecu?
Does this ecu come with different resistor configurations?
Logged
prj
Hero Member
*****

Karma: +1072/-480
Offline Offline

Posts: 6035
« Reply #8 on: July 16, 2019, 01:48:52 AM »
The ECU is supposed to have a 29F400BB, not a BT.
Of course the CBOOT can never write the ECU if there is a BT in there, as the memory layout is wrong.

Fit the correct chip and your problem is solved.
Logged
PM's will not be answered, so don't even try.
Log your car properly - WinOLS database - Tools/patches
aef
Hero Member
*****

Karma: +69/-46
Offline Offline

Posts: 1600
« Reply #9 on: July 16, 2019, 02:08:33 AM »
thank you prj
Logged
Pages: [1]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 23, 2024, 05:00:01 PM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 16 queries. (Pretty URLs adds 0s, 0q)