Passat 1.8t ATW, DBW- Help with ABS coding

Pages: 1 [2]

« previous next »

Author

Topic: Passat 1.8t ATW, DBW- Help with ABS coding (Read 18668 times)

ddillenger

Hero Member

Karma: +641/-21
Offline

Offline

Posts: 5640

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #15 on: July 07, 2013, 10:55:17 AM »

Get a DVOM and go to town. There are 3 that I use.


	Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM

kg6dxn

Newbie

Karma: +0/-0
Offline

Offline

Posts: 9

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #16 on: July 07, 2013, 11:11:01 AM »

Assuming boot mode is possible. How would one disable the ABS? I just need to disable the reporting over the gateway.
VCDS log shows this in the 01 Engine module

Quote

17931 - Crash Signal from Airbag Controller
P1523 - 35-00 - Implausible Signal
18057 - Powertrain Data Bus
P1649 - 35-00 - Missing Message from ABS Controller


	Logged

BDK

Jr. Member

Karma: +2/-0
Offline

Offline

Posts: 28

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #17 on: July 07, 2013, 03:15:37 PM »

Are you actually getting an abs light or just the brake warning light?


	Logged

kg6dxn

Newbie

Karma: +0/-0
Offline

Offline

Posts: 9

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #18 on: July 07, 2013, 03:38:55 PM »

Quote from: BDK on July 07, 2013, 03:15:37 PM

Are you actually getting an abs light or just the brake warning light?

Not sure about the actual light, I opened the cluster and painted the LED's black. But I believe they were on and that's why I painted them. In fact, I think both ABS and brake pad warning lamps were on.

The warning is on the multifunction display. It says: "STOP, Service Manual" every time it does, the dash "Dings" an alarm. This message cycles over and over. I did open the cluster and de-solder the buzzer but the display cannot be cleared. The same display also reports outside air temp and fuel economy along with every other engine related problem. I can only see temp and economy for 2 seconds when the car first starts. If I can interrupt the ABS signal, the system will be fully functional.

Normally the ABS reports status to the ECU. Since I don't have ABS, it is in constant alarm.

Nobody I'm aware of can program out the alarm from the cluster and the cluster shows no codes.

Here is the entire scan... BTW, the air bag code only lights up the lamp and does not effect driveability.

Quote

--------------------------------------------------------------------------------

Chassis Type: 3B - VW Passat B5
Scan: 01 02 03 08 15 16 17 19 35 36 37 46 47 55 56 57 58 75 76 77

Mileage: 470km/292miles
-------------------------------------------------------------------------------
Address 01: Engine Labels: 058-906-018-ATW.lbl
Part No: 4B0 906 018 BG
Component: 034GTMBCELIM G 91R1
Coding: 07501
Shop #: WSC 78901
VCID: 67DD73D005856320811

2 Faults Found:
17931 - Crash Signal from Airbag Controller
P1523 - 35-00 - Implausible Signal
18057 - Powertrain Data Bus
P1649 - 35-00 - Missing Message from ABS Controller

Readiness: 0010 0100

-------------------------------------------------------------------------------
Address 17: Instruments Labels: 3B0-920-xx2-17.lbl
Part No: 3B0 920 920 B
Component: B5-KOMBIINSTR. VDO V26
Coding: 00235
Shop #: WSC 05311
VCID: 1D311138975979F02BD

0 Faults Found:

-------------------------------------------------------------------------------
Address 19: CAN Gateway Labels: 6N0-909-901-19.lbl
Part No: 6N0 909 901
Component: Gateway K<->CAN 0001
Coding: 00000
Shop #: WSC 05314
VCID: F0EF988CB04B249850B

0 Faults Found:

End ---------------------------------------------------------------------


	Logged

ddillenger

Hero Member

Karma: +641/-21
Offline

Offline

Posts: 5640

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #19 on: July 07, 2013, 05:38:52 PM »

Read the tune, email it to me (please don't post it openly), Send me a list of the DTC's in the engine computer with the file and I'll manually remove them from the flash. If you still get a warning, more investigation will be needed.


	Logged

Carsinc

Sr. Member

Karma: +17/-2
Offline

Offline

Posts: 447

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #20 on: July 07, 2013, 08:19:39 PM »

Thats the best offer you could ever hope for.


	Logged

kg6dxn

Newbie

Karma: +0/-0
Offline

Offline

Posts: 9

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #21 on: July 07, 2013, 08:29:47 PM »

Quote from: ddillenger on July 07, 2013, 05:38:52 PM

Awesome! It will take me a few days to get back to you.

I don't want to post the file openly since it is 034's proprietary tune.

Now is it as simple as grounding the pin?
1) disconnect battery
2) ground pin
3) turn key on
4) Connect battery
5) remove ground at pin
6) read flash

Is that it? Do I use the NefMoto or do I need a third party program to read from boot?


	Logged

Carsinc

Sr. Member

Karma: +17/-2
Offline

Offline

Posts: 447

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #22 on: July 07, 2013, 08:33:22 PM »

I use a galletto 1260 clone off ebay, I was told they suck MPPS will do the same I'm told their better Wink


	Logged

byzan a4

Full Member

Karma: +0/-1
Offline

Offline

Posts: 73

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #23 on: July 30, 2013, 03:22:18 PM »

Quote from: kg6dxn on July 07, 2013, 11:11:01 AM

Assuming boot mode is possible. How would one disable the ABS? I just need to disable the reporting over the gateway.
VCDS log shows this in the 01 Engine module

I too am intrigued about removing these from ME7.5 WB converted cars. They have no bearing on adaptions but scare the customers seeing it because they expect a clean code read. The issue is this, The cars are early ME7.1's and the component parts won't support these missing parts being wired in.
Should i convert the P code to hex and dig further through the hex?

TIA


« Last Edit: July 31, 2013, 04:23:26 AM by byzan a4 »	Logged

nicktruman

Newbie

Karma: +2/-0
Offline

Offline

Posts: 15

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #24 on: April 22, 2020, 09:44:39 AM »

Hi, Did this ever work? I too have no ABS and the cluster isn't happy, i get a STOP Brake fault Service Manual message on the multi function display, the buzzer has long gone!

I coded ABS out of the CAN gateway but message wont go.

VW 20v 1.8T AWT me7.5 ecu and immo3 dash from 2002 Passat

Any ideas? I've been through Ross Tech's stuff.. and cant find anything, is there a way to trick the ecu that the ABS is fine?

I have a dump of the dash if that helps anyone please.

Kind regards
Nick


	Logged

_nameless

Hero Member

Karma: +342/-466
Offline

Offline

Posts: 2802

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #25 on: April 22, 2020, 04:37:39 PM »

Quote from: kg6dxn on July 06, 2013, 09:15:13 PM

The ECU is a 4B0 906 018 BG. Dazq tried to help me via remote Teamviewer. 034 Motorspot locked the ECU and it can't be read. I opened the case in hopes to ground pin 24, boot mode but they epoxied all over the eprom. I think I will do more damage trying to remove the epoxy.

Not sure what to do. I guess I need to take it back to 034 for an update.

Any ideas?

oh t knife the ide of the flash chip just enough so you can get to the boot pin


	Logged

Giving your mom a tuneup

BlackT

Hero Member

Karma: +79/-40
Offline

Offline

Posts: 1425

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #26 on: April 22, 2020, 10:59:32 PM »

Quote from: nicktruman on April 22, 2020, 09:44:39 AM

Simply code out ABS via VCDS in ECU. That will get rid of DTC in ECU, but i don't know is it posible to code it out cluster with VCDS


	Logged

Auriaka

Full Member

Karma: +17/-2
Offline

Offline

Posts: 113

	Re: Passat 1.8t ATW, DBW- Help with ABS coding « Reply #27 on: April 22, 2020, 11:41:36 PM »

would CAN_C and CAN_R have any effect upon trying to resolve this?
Curious question out of academics


	Logged

Pages: 1 [2]

« previous next »

Jump to:

Navigation

Personal Tools

November 28, 2024, 11:53:18 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search