NefMoto > Technical > NefMoto Software > Could not open FTDI device NEWB help please
Pages: 1 [2]
« previous next »
Author Topic: Could not open FTDI device NEWB help please  (Read 19825 times)
nattyS4
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15
« Reply #15 on: August 21, 2013, 11:54:57 AM »
what do you mean powered? like did i turn the ignition key?
Logged
nattyS4
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15
« Reply #16 on: August 21, 2013, 11:57:07 AM »
yes patience is definitely key.....it's just hard when ur pumped to get your tune on your car lol.  I dunno hopefully i figure it out.  And i will def post a thread after words so i can hopefully help the next guy.
Logged
nattyS4
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15
I am getting "Failed to read test echo from FTDI device make sure device is plugged into OBD and in dumb mode"

I'm using comm port 3,
the driver installed is FTDI 2.8.30.0.
It says the device plugged in is FTDIBUS/VID_0403+PID_6001+A9YXP7ZVA\0000.

Is this a cable issue or driver issue?

I installed VCDS lite to check and see if that worked but I downloaded the most recent version which i don't think is the right version for an Ebay cable? but when i tested it in VCDS i got

Port status: ok
Interface: Not found

Any help would be greatly appreciated.
Thanks again,
Jake
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #18 on: August 22, 2013, 10:09:34 AM »
Quote from: nattyS4 on August 21, 2013, 11:54:57 AM
what do you mean powered? like did i turn the ignition key?

yes.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
phila_dot
Hero Member
*****

Karma: +173/-11
Offline Offline

Posts: 1709
« Reply #19 on: August 22, 2013, 10:14:24 AM »
In both cases you're not connected to a powered ECU.
Logged
nattyS4
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15
« Reply #20 on: August 22, 2013, 10:35:23 AM »
But what if I am? i'm plugged in and the key was turned on..... why would my ECU not have power?
Logged
phila_dot
Hero Member
*****

Karma: +173/-11
Offline Offline

Posts: 1709
« Reply #21 on: August 22, 2013, 10:37:48 AM »
Is the MIL lit?

Are you sure your OBD port is functional?
Logged
nattyS4
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15
« Reply #22 on: August 22, 2013, 10:46:40 AM »
MIL=light on the cable? yes its on, would that mean OBD port is good to go?
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #23 on: August 22, 2013, 11:03:59 AM »
Quote from: nattyS4 on August 22, 2013, 10:46:40 AM
MIL=light on the cable? yes its on, would that mean OBD port is good to go?

MIL is "malfunction indicator light" on cluster (also known as "check engine light" or CEL)

but yea, the light on the cable means its good to go. Something else is wrong, unfortunately.
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
nattyS4
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 15
« Reply #24 on: August 22, 2013, 11:14:27 AM »
Yeah i have no CEL light and the light on the cord itself is on.  Any other thoughts? did you guys check out the information i put up above? listing the driver and the device i'm using? does that look correct?
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #25 on: August 22, 2013, 11:19:44 AM »
Quote from: nattyS4 on August 22, 2013, 11:14:27 AM
Yeah i have no CEL light

The CEL light should be on if the ignition is on and the cable is plugged into the OBDII

Can you "licensing -> save info to file" and "licensing -> check if fdti devices support licensing" and attach the output?
Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #26 on: August 22, 2013, 11:31:39 AM »
Also, download and install FT_Prog... we can get more information about what cable you have using that.

http://www.ftdichip.com/Support/Utilities.htm#FT_Prog

hit f5 (or devices->scan and parse) and post a screenshot of what you see

You can also "hover" over the ftdi device as described here
http://nefariousmotorsports.com/forum/index.php/topic,325.0title,.html
« Last Edit: August 22, 2013, 11:43:42 AM by nyet » Logged
ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Pages: 1 [2]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 26, 2024, 05:58:03 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)