Pages: [1] 2
Author Topic: Hello from New York City  (Read 18092 times)
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« on: August 26, 2013, 11:05:02 PM »

Hello everyone. Newbie here. I registered a few months ago looking for information on how to delete immobilizer for my audi. Now a little history on myself. Fix BMW for a living. VW and audi is my fun. I got a b5 a4 FWD from a friend for free with a blown motor. Was going to rebuild the motor but got a great deal on a 2.7l motor complete with ecu out of a 2001 audi a6. Decided hey how hard can it be to put in a B5 A4. Ok so a year later finally got around to putting the motor in. Man I thought going the wiring was hard, getting rid of the immobilizer is the worst. I tried a ecu from a 2000 s4 no good.  Now i want to try and program it out. But there is so much info I don't know where to start. The hardest part for me is figuring out/understanding what a lot of the info means. So with that said I would like to say THANK YOU to everyone that post all the help info that I have been reading.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12256


WWW
« Reply #1 on: August 26, 2013, 11:08:59 PM »

If your 2000 s4 ECU is north american, it should have worked assuming you had it coded right and a bosch MAF.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #2 on: August 27, 2013, 06:16:45 AM »

I try to change the soft coding but it wouldn't take and don't have a Bosch maf. Can get one. However  It keeps logging a fault for the epc light & malfunction light don't remember the fault codes at the moment. What happens is the engine starts and the idle jumps up then engine shuts off. I don't think the Ecu good has a permanent fault for engine coolant temp. But any ideas is greatly appreciated
Logged
jackson.amrol@gmail.com
Full Member
***

Karma: +4/-6
Offline Offline

Posts: 128


"you sir are an animal"


WWW
« Reply #3 on: August 27, 2013, 08:15:55 AM »

Did you successfully immo off the ecu that came with the motor? My 2001.5 C5 came with immo3 active.

I had the coolant temp dtc after tearing my beast down. The connector was just hanging out under the res, it was on when i put it on but pops off easy if the plug isn't seated 100% and you pull to the get the res. on top of its mounting tabs. <- simple things man, simple things...
Logged

Lost, No.. My minds around here somewhere..
Shh, I'm calling my mom.. "It's 3AM" SHH!
Mom, is there such a thing as kosher pork?
"I'm not bailing you out tonight"...
ddillenger
Hero Member
*****

Karma: +641/-21
Offline Offline

Posts: 5640


« Reply #4 on: August 27, 2013, 08:31:13 AM »

Also, the s4 ecu cannot be softcoded 06712 for the A6. You must code it 06711, then the coding will be accepted and retained. Functionally there is no difference. HOWEVER, the softcoding will not allow you to run a different MAF, you must flash a different file. 8D0907551M is for a hitachi MAF. I'd say start there.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12256


WWW
« Reply #5 on: August 27, 2013, 09:06:48 AM »

Did you successfully immo off the ecu that came with the motor? My 2001.5 C5 came with immo3 active.

He's not using the ECU that came with the motor...
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12256


WWW
« Reply #6 on: August 27, 2013, 09:07:51 AM »

don't remember the fault codes at the moment

If you expect to make meaningful progress, you're going to have to take note of the actual codes.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #7 on: August 27, 2013, 09:45:23 AM »

Im working on immo off. Try to use hex editor to see if I can change to immo off. Going to try that later.
Logged
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #8 on: August 27, 2013, 09:52:41 AM »

I check the faults that the s4 ecu have. Check wires connector, power and ground good. No short or damage wires. Also I have 2 a6 ecu and neither on log those faults. I tried the soft code u stated but still didn't take. Don't if it's because it's looking for the automatic transmission.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12256


WWW
« Reply #9 on: August 27, 2013, 09:53:34 AM »

Im working on immo off. Try to use hex editor to see if I can change to immo off. Going to try that later.

The only 2000 S4 ecu's with immo are not North American.

Where did you get the ecu?
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #10 on: August 27, 2013, 11:41:53 AM »

Ur rite it does have immo. But the ecu I got with the motor is from 01 a6 which does have immo. That's the ecu im talking about.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12256


WWW
« Reply #11 on: August 27, 2013, 03:14:47 PM »

You said you had a 2000 s4 ecu. That should work if it is a 1Mb version

flash mbox on to it, and call it a day.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #12 on: August 27, 2013, 09:21:12 PM »

Having problems connecting in bootmode with all 3 ecu. What I'm I doing wrong. Keep getting disconnected see attachment. Anyone ran into this.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12256


WWW
« Reply #13 on: August 27, 2013, 09:23:20 PM »

are you doing bootmode on a bench harness?

if not, how are you doing it in car?

and why are you using bootmode at all? you dont need it for the s4 ecu if it doesn't have immo.

finally, please use print screen don't take a picture of your screen geez
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Mistashotta
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 11


« Reply #14 on: August 27, 2013, 09:49:33 PM »

Sorry for the pic. I'm using the iPad. Ok help me out here this is what I have. I do have a 2000 s4 ecu 8d0 907 551 b and 2 a6 ecu 4b0 907 551 t. Now the s4 ecu have a permanent fault for the ECT sensor. I clear it it comes rite back. Replace sensor. Wiring is good. So unless it coding then this ecu is defective.  Also it starts an shut off like it has an immo. The a6 ecu have immo. I can't even read flash I get disconnect with message immo not authenticated. I have all the immo off files but it seems I don't have the proper memory layout.
Logged
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.021 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)