|
Dave9n3
|
 |
« on: January 22, 2016, 03:29:54 AM »
|
|
|
Hi,
I'm interested in taking an EEPROM dump of my instrument cluster as a backup. I have vag+k can commander 2.5 and also vagdashcom.
I also have a dumb FTDI cable that I use with nef flasher, I'm assuming I should be able to use this cable with either of the two above mentioned bits of software?
Is there anything I should be aware of before I take a copy of the data safety wise so I don't muck anything up.
TIA
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #1 on: January 22, 2016, 03:43:07 AM »
|
|
|
Use EEPROM Programmer 1.19 with your FTDI cable and it'll work fine.
Or can commander with the FTDI cable, make sure its set to k-line. Choose appropriate cluster and read.
I find 1.19 to be more reliable.
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #2 on: January 22, 2016, 04:57:32 AM »
|
|
|
adam can you attach a clean virus free 1.19 programmer or point me to the thread where i can find it.
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #3 on: January 22, 2016, 06:38:46 AM »
|
|
|
I'll upload it when I get home. Don't let me forget.  |
|
|
|
|
Logged
|
|
|
|
|
Dave9n3
|
|
« Reply #4 on: January 22, 2016, 08:54:10 AM »
|
|
|
Awesome cheers Adam I was worried as I heard the VDO clocks can be a pain. I was also told the dump would be encrypted? Not sure how true that is though |
|
|
|
|
Logged
|
|
|
|
|
Lost
|
|
« Reply #5 on: January 23, 2016, 01:52:35 AM »
|
|
|
I'll upload it when I get home. Don't let me forget. Please do. Thank you. |
|
|
|
|
Logged
|
|
|
|
|
Dave9n3
|
|
« Reply #6 on: January 25, 2016, 10:24:03 AM »
|
|
|
This is what you're after i think?
|
|
|
|
|
Logged
|
|
|
|
|
Dave9n3
|
|
« Reply #7 on: January 25, 2016, 10:28:37 AM »
|
|
|
To add to my thread, i tried to get a read from the instrument cluster but was unable to get a complete read. the data would stop reading mid way through. Ive used VAG K+Can 2.5, VAG eeprom programmer 1.19 and VAG k pin reader. Is there any reason why i may not have been able to get a full read. Using a normal ftdi kkl cable.
here is the read i managed to get.
|
|
|
|
|
Logged
|
|
|
|
|
Lost
|
|
« Reply #8 on: January 25, 2016, 12:10:27 PM »
|
|
|
This is what you're after i think?
Thank you very much!! |
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #9 on: January 25, 2016, 12:11:38 PM »
|
|
|
Well if that isn't stolen off my Google drive I dunno what is.  |
|
|
|
|
Logged
|
|
|
|
|
Dave9n3
|
|
« Reply #10 on: January 25, 2016, 02:44:47 PM »
|
|
|
sorry Adam, shameful i know  though it may have saved you some time |
|
|
|
|
Logged
|
|
|
|
Lupsnow
Newbie
Karma: +0/-0
 Offline
Posts: 8
|
|
« Reply #11 on: January 30, 2016, 04:44:00 AM »
|
|
|
I tried to read my valleo immo 3 eeprom 24c04 with the vag eeprom programmer v1.19g but I can't seem to connect to anything with it...
I have a rosstech 12.12 Hex+can clone usb cable. The cable works without any problems for VCDS 12.12.3. But any other software I try doesn't work even with boot in intelligent mode unchecked...
I have the rosstech vcp drivers installed and loaded.
I tried in the eeprom programmer set on usb connection and com 1.
|
|
|
|
|
Logged
|
|
|
|
|
adam-
|
|
« Reply #12 on: January 30, 2016, 08:55:30 AM »
|
|
|
Try a dumb cable. Is it assigned to Com 1?
|
|
|
|
|
Logged
|
|
|
|
Lupsnow
Newbie
Karma: +0/-0
Offline
Posts: 8
|
|
« Reply #13 on: January 31, 2016, 09:45:26 AM »
|
|
|
I ordered a new cable... So I will see if it works than.
But thanks for your reply!
|
|
|
|
|
Logged
|
|
|
|
|
Dave9n3
|
|
« Reply #14 on: February 01, 2016, 03:24:34 PM »
|
|
|
Still unable to get a cluster read of mine  I've tried a fair few programs and it seems to say EEPROM area blocked. Dash is VDO V06 |
|
|
|
|
Logged
|
|
|
|
|
