Recent Posts

Newer Software for your car. 2004 update, i have kvb on it

Thank you!

Sorry for the late follow-up, I´ve not had much spare time lately but I tried this one out in the car and it did not work well.
So I decided to go to the dealer and get the ECU updated.
Software went from 30653124B 40LKMA.A2L to 30729127A 40LPHJ.A2L, Most annoying part is that I cannot see KVB in this version either 
I have attached binary read from the ECU after the update

Big thanks! I missed this message early.

you never seen this! hahha i been going through this bin on my spare time since. i have the map sensors ready, and a spare manifold to put a bung in.
one day i'll fuck with it

Are you sure your car has DECOS at all? In 40GPHJ there are no DECOS maps.

yea 40 series and lower and not decos, they're fixed 50series is decos  we have LPT DECOS 04.5+ and all T5 and R, in the EU its only the T5 and R hence the post 04.5+ 40 series bins.

use a top hat from a pump that doesnt have the regulator and use a referenced fuel pressure regulator on the Rail so it'll scale 1:1 with boost if you're going for a higher power non decos car

If you want to do it the cracking pressure ratio way in KFVPDKSD/E, then you have to change CWPLGU.
Because 551K software does not have this codeword configurable, you need to make a patch to set base boost to pu_w instead of what is calculated in IIRC LDRPLS.

If you can't do that then you need to do it completely differently by changing LDRPLS, so like your 2nd option and don't touch KFVPDKSD/E.

[Target]

Hello

Target
I want to adapt the software 8D0907551K from my RS4 B5 to the new base charge pressure (waste gate cracking pressure) of the new turbochargers. The original waste gate cracking pressure is approximately 400 mBar (6 PSI) and now it is approximately 900 mBar (14 PSI).



Possible solutions
I have read in the forum about four different solutions to made this adjustment. As far as I understand, only the following two solutions are possible in my case:



Solution no.1
Only adjust the vpssplg axis of KFVPDKSD and KFVPDKSE maps.

The KFPLGUB and KFDPLGU maps do not exist in the DAMOS of 8D0907551K. This means that I cannot directly modify the calculation of plgrus_w. However, I know the calculation for vpssplg:

RS4: plgrus_w = Output of KFPLGU/B
vpssplg = pssol_w/plgrus_w. vpssplg is the axis for KFPVDKSE/D

vpssplg (Druckverhaltnis Saugrohrsolldruck zu Grundladedruck) = pssol_w (Sollsaugrohrdruck) / plgrus_w (Grundladedruck Sollwert).

According to

cracking pressure is ratio = 1

, the axis vpssplg has the value 1 for the base charge pressure. I assume that the original base charge pressure has the value 1400mBar.
If I use the assumed original value of 1400mBar for plgrus_w in the calculation and use the new base charge pressure of 1900mBar for pssol_w, I get the following ratio value: 1900mBar / 1400mBar = 1.357142857142857.

The ratio of plgrus_w = 1.357142857142857 therefore corresponds to the new base charge pressure of 1900 mbar.

The values of the axis vpssplg_w of the maps KFVPDKSD and KFVPDKSE multiplied by the factor 1.357142857142857 results in:




In comparison, the original values:



Solution no.2
Only change the KFVPLGU map according to

...First ...get a 3rd gear log of my "base boost pressure" with 0% WGDC. I used that data to fill in the last column of KFVPLGU, and then adjusted the rest of the map to keep the same shape as stock but increased for my new wastegates (15-16 psi). With it set up this way, the ECU knows to control boost under the wastegate pressure with the throttle plate (no need to change the vpssplg_w axis for KFVPDKSD/E).

...KFVPLGU ...I set all the rpm rows before I hit my peak boost to the same value, I'm not sure if I was correct in doing that.. but I haven't noticed any ill effects...

OEM values:


Values adapted to the new waste gate cracking pressure:




Question to the forum
Do you recommend solution no.1 or no.2 for me? Or is there another solution variant that is better and I'm able to do (please be aware, I'm haven't the skill to change assembler code)?

Hello, a short update. I fitted the EDC16U1 with the number 03G906016FF but just reflashed it with a flash from a DSG car so that in the VCDS i could code it to DSG.

The car is working and in the moment i have a couple of things to sort out. First, my AC is not working, as in not starting at all, when i switch on the climatronic the fans are not spinning and the clutch is not engaged as there is no cold air. In the ECU connectors there are no wires in the place where the Klimaanforderung is (E_S_AC technical description) and in my EDC15 there is a wire.

Second i have also a wire for Motorluftrelais (A_T_MLR) but on EDC16 there is Kuhlerventilator (A_T_LUES1). When i connect those wires the fans start spinning with ACC on, and after the key is removed they keep spinning for about 5 s.

Third problem is, the ECU is reporting a fault for brake switch, although the DSG and the ABS can see the brake switch and it is operating normal in abs and DSG measuring blocks.

And the last issue that i have is the ASV. On EDC16 it is electronically operated but mine is vacuum operated. I found the wires on the connector and tried to use just the wires for the motor but as soon as i start the car the ASV shuts and the engine dies. I guess hier i will have to feed the ECU a signal so that it thinks the ASV is open. I should have somewhere on the ECU a 5V free pin which i could short with the input pin for the ASV but is this correct, is the voltage 5V for an open ASV on golf mk5.

Is there someone who has done something similar or is willing to help.

On the picture
KFZW -> 121EA
KFZW2 -> 122AA
8-bit values
GradKW = value * 0.75

Hello
How to find the ignition advance angle map in me 7.5 06A906032FK 3940 This is 2.0 not 1.8Turbo ? There is no damos for it anywhere.
I want to change the ignition for LPG
Any advice, map size, anything ?
Greetings

Hey,

I read my ME731 ecu and saved eeprom file with this tool. I'm editing hex file. I tried flash this file to eeprom but it didnt verify. Then i read eeprom and save the file again. It seems nothing changed in the eeprom.

I attached eeprom .bin file i read. I want to virginate my ECU.

Hello everyone, I have a similar problem and would like to ask you to evaluate, maybe improve the software of this ecu.