Pages: 1 2 [3] 4 5 ... 9
Author Topic: Ignition cut rev limiter me7  (Read 121848 times)
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #30 on: November 11, 2016, 12:36:45 AM »

Mhmm.  That said, my stock head was holding this abuse plus NLS/AL every few days for 3 years.  Stock turbo too.  No damage to fins, no lack of boost, no damaged valves when I pulled the head.  People worry a lot; but if you can fix it, why not?
Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #31 on: November 11, 2016, 09:36:03 AM »

This can be stickied.  Those settings work pretty damn well.  I don't have a video, it's too hard to hold onto a FWD spin in 2nd in the wet. 

Someone else can try it and LMK. Smiley
Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #32 on: November 13, 2016, 11:07:38 AM »

https://www.youtube.com/watch?v=T8pFU-oZ3Pk&feature=youtu.be

Have a video. Smiley
Logged
contrast
Full Member
***

Karma: +20/-2
Offline Offline

Posts: 215


« Reply #33 on: November 13, 2016, 03:59:28 PM »

Sounds legit!
Logged
vwaudiguy
Hero Member
*****

Karma: +53/-37
Offline Offline

Posts: 2024



« Reply #34 on: November 13, 2016, 05:47:51 PM »

I like this one. Lol. Looks like all fucking hell's breaking loose.

https://www.youtube.com/watch?v=IW5COieCR88
Logged

"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
fknbrkn
Hero Member
*****

Karma: +176/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #35 on: November 13, 2016, 06:09:52 PM »

ok i got it. the problem was e_lm active because of mafless
https://youtu.be/NujUfLReBAI

KFTSRL, NMAX

KFSZT irrelevant here. its hardcoded in asm to be used only below 1500 rpm
i`ll try different values later
« Last Edit: November 13, 2016, 06:11:42 PM by fukenbroken » Logged
adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #36 on: November 14, 2016, 01:01:36 AM »

Decent. Smiley I need to learn how to IDA properly.
Logged
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #37 on: November 14, 2016, 03:09:22 AM »

Cool stuff, this makes a burnout so much more interesting  Grin
Logged

adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #38 on: November 15, 2016, 12:44:35 AM »

https://www.youtube.com/watch?v=Khdv8bsN9fI
https://www.youtube.com/watch?v=_pO99FeIYFk

Logged
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #39 on: November 15, 2016, 07:34:44 AM »

Did you place both NMAX and NMAXOG above the 0 dwell rpm?
Logged

fknbrkn
Hero Member
*****

Karma: +176/-18
Offline Offline

Posts: 1401


mk4 1.8T AUM


« Reply #40 on: November 15, 2016, 08:00:48 AM »

+ 50rpm for me

also we should play with KFZWMN / KFZWOP areas i think
Logged
TijnCU
Hero Member
*****

Karma: +60/-4
Offline Offline

Posts: 690


flying brick


« Reply #41 on: November 21, 2016, 09:04:16 AM »

https://youtu.be/0Jn13D0iWeo  Grin
Pops really good. Poor valvetrain  Smiley
Logged

adam-
Hero Member
*****

Karma: +122/-33
Offline Offline

Posts: 2177


« Reply #42 on: November 21, 2016, 10:57:44 AM »

You need to teach me how to IDA! Smiley
Logged
Silencesilja
Newbie
*

Karma: +2/-2
Offline Offline

Posts: 12


« Reply #43 on: February 15, 2017, 06:30:39 AM »

first day into hard limiter,and she gives you this look..
Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #44 on: February 15, 2017, 06:35:07 AM »

first day into hard limiter,and she gives you this look..


Yeah this'll do that to a old rusty stock exhaust, and it'll melt/damage your cat Smiley
use it as a good excuse to get at proper stainless system Wink
Logged
Pages: 1 2 [3] 4 5 ... 9
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.048 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)