|
|
marto7
Full Member
Karma: +1/-1
 Offline
Posts: 67
|
 |
« Reply #61 on: September 24, 2019, 02:53:13 PM »
|
|
|
Will check again tommorow for DTC and VCDS connection. Like BlackT mentioned, maybe my ecu wont work with Nefmoto. Too bad
|
|
|
|
|
Logged
|
|
|
|
|
|
marto7
Full Member
Karma: +1/-1
Offline
Posts: 67
|
|
« Reply #63 on: September 25, 2019, 02:45:48 AM »
|
|
|
Dont know what means pick different binary. Also tried to open the file that i want to flash with winols 8bit search or HxD but on both i dont have any results.Nothing close to the fix in the topic.
And if fix worked, should i do it every time im exporting new file for flash ?
|
|
|
|
|
Logged
|
|
|
|
marto7
Full Member
Karma: +1/-1
Offline
Posts: 67
|
|
« Reply #64 on: September 25, 2019, 08:20:11 AM »
|
|
|
Yes the fix is worked. With little help found the line that should change and now the problem is gone.Thanks.
Want to ask, if Diff write flash i good option ? Tried it 5 times today and work good.Should i use full flash from time to time or when i have only little correction i can use Diff flash ?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #65 on: September 25, 2019, 08:37:49 AM »
|
|
|
Yes, fast write should always work.
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
|
carsey
|
|
« Reply #66 on: September 29, 2019, 05:01:50 AM »
|
|
|
Struggling to get this downloaded and installed right. Downloaded the fully functional version off the github. But cant seem to find out how to get it installed. THe .msi installs the 1.9.4.3 version of the flasher, but still cant see any fast write part of it.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #67 on: September 29, 2019, 09:34:03 AM »
|
|
|
"fast" is actually "diff write"
|
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
|
carsey
|
|
« Reply #68 on: September 29, 2019, 10:41:53 AM »
|
|
|
Thats what I normally use when flashing. Normally takes in region of 4mins 30seconds.
Thought you could get it much quicker than that?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #69 on: September 29, 2019, 11:13:05 AM »
|
|
|
Thats what I normally use when flashing. Normally takes in region of 4mins 30seconds.
Thought you could get it much quicker than that?
The less you modify the less it will have to write. Also you can try increasing baud rate. |
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
|
carsey
|
|
« Reply #70 on: September 29, 2019, 12:15:32 PM »
|
|
|
even a 1x1 KRKTE byte will take the same amount of time  Normally have 10400 baud rate with a VCDS lead |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #71 on: September 29, 2019, 12:19:02 PM »
|
|
|
even a 1x1 KRKTE byte will take the same amount of time Normally have 10400 baud rate with a VCDS lead That's about as fast as it will go, since even a single byte change alters quite a few checksums. Also, because of the way flash works, changing a single byte requires erasing and rewriting an entire flash sector. |
|
|
|
|
Logged
|
ME7.1 tuning guideECUx PlotME7Sum checksumTrim heatmap toolPlease do not ask me for tunes. I'm here to help people make their own. Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
|
|
|
|
adam-
|
|
« Reply #72 on: October 02, 2019, 07:31:33 AM »
|
|
|
It shouldn't take 4 minutes 30. Single/small changes typically take ~1 minute for me.
|
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #73 on: October 02, 2019, 07:54:26 AM »
|
|
|
My flash time is always 1 min 20sec to 1min 40 sec
No mather if I change 1 byte or 10 scalars and 10 maps
Diff write, baudrate max
|
|
|
|
|
Logged
|
|
|
|
marto7
Full Member
Karma: +1/-1
Offline
Posts: 67
|
|
« Reply #74 on: October 02, 2019, 02:09:49 PM »
|
|
|
With diff write im always 1.50 to 1.55, no matter what im changing.My file is 1mb.Using Baud - 38400
|
|
|
|
|
Logged
|
|
|
|
|
