Pages: [1]
Author Topic: 1C0920951J KOMBI+WEGFAHRS. M73 V02 (04 Beetle Turbo S 6MT, Marelli)  (Read 7851 times)
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36



I attached the file I pulled from it with vagtacho, I dont know if it is pulled correctly. Car runs, immo and vin are correct and keys are matched just fine, but I have a steady ON immobilizer light. When I reset the cluster it jumps back to the mileage it was when I first pulled the skc (pin 2116). When I log into instruments with the code in vcds and then go put the same pin in adaptation block 50 (this is not a cluster swap, its the original cluster, and the ecu is NOT immo defeated), it just says "Wait" rather than grabbing the vin/immo id again and adapting.

Also, vagtacho tells me the pin is 0324, but that pin fails lol, 2116 is what has worked for both ecu and cluster.

I dont know if someone can provide a zeroed out eeprom or what, maybe its just a bad checksum? Bad mileage change? IDK, but this is really frustrating me, I dont even know if I pulled the bin right...

Vin and immo if it matters: 3VWFE31C64M405673     VWZ5Z0C7161043
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2800



« Reply #1 on: April 11, 2018, 03:34:04 AM »

the read you posted is shit. you wont be pulling any info from variant a4 chassis cars with a clone vagtacho.
Logged

Giving your mom a tuneup
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #2 on: April 11, 2018, 08:06:55 AM »

Who says its a clone? Anyways, how SHOULD I read it via odb2 port? I can't get the eeprom flasher to communicate
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Offline Offline

Posts: 2800



« Reply #3 on: April 11, 2018, 08:18:51 AM »

Who says its a clone? Anyways, how SHOULD I read it via odb2 port? I can't get the eeprom flasher to communicate
because real tools dont have issues reading this cluster, clones do.  If you did youd have a original tool youd have factory support and not asking online form for help. Tongue
Logged

Giving your mom a tuneup
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655


« Reply #4 on: April 11, 2018, 09:18:02 AM »

eh, vagtacho sucks on any MM cluster. genuine or not.

i use carprog for audi/beetle mm cluster. 100% success.
Logged
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #5 on: April 11, 2018, 10:21:08 AM »

eh, vagtacho sucks on any MM cluster. genuine or not.

i use carprog for audi/beetle mm cluster. 100% success.

Thanks for legit help. Wouldnt happen to have an original dump in case mine is not recoverable would you?
Logged
k0mpresd
Hero Member
*****

Karma: +146/-54
Offline Offline

Posts: 1655


« Reply #6 on: April 14, 2018, 07:24:46 PM »

attached.
Logged
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #7 on: April 17, 2018, 03:05:38 AM »

attached.

Thanks! So is carprog the only way I should flash this (I dont have one yet) or do you think flashing with tacho might work?
Logged
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #8 on: April 17, 2018, 03:28:54 AM »

I noticed thats a format match to the last 2048 bytes of my eep dump with tacho, ill see how it works out tomorrow if I cant get a proper 2048 only Ill add the garbage data to the top 2048 and try flashing that:

Code:
head -c2048 1C0920951J.eep > 1C0920951J_top_2048.eep
cat 1C0920951J_top_2048.eep 2002\ BEETLE\ TURBO\ S\ 1C0920951JX\ 117600KM.bin > 2002\ BEETLE\ TURBO\ S\ 1C0920951JX\ 117600KM.eep
vbindiff 1C0920951J.eep 2002\ BEETLE\ TURBO\ S\ 1C0920951JX\ 117600KM.eep
« Last Edit: April 17, 2018, 03:31:54 AM by miigotu » Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.017 seconds with 19 queries. (Pretty URLs adds 0s, 0q)