Pages: [1]
Author Topic: 1C0920951J KOMBI+WEGFAHRS. M73 V02 (04 Beetle Turbo S 6MT, Marelli)  (Read 8770 times)
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36



I attached the file I pulled from it with vagtacho, I dont know if it is pulled correctly. Car runs, immo and vin are correct and keys are matched just fine, but I have a steady ON immobilizer light. When I reset the cluster it jumps back to the mileage it was when I first pulled the skc (pin 2116). When I log into instruments with the code in vcds and then go put the same pin in adaptation block 50 (this is not a cluster swap, its the original cluster, and the ecu is NOT immo defeated), it just says "Wait" rather than grabbing the vin/immo id again and adapting.

Also, vagtacho tells me the pin is 0324, but that pin fails lol, 2116 is what has worked for both ecu and cluster.

I dont know if someone can provide a zeroed out eeprom or what, maybe its just a bad checksum? Bad mileage change? IDK, but this is really frustrating me, I dont even know if I pulled the bin right...

Vin and immo if it matters: 3VWFE31C64M405673     VWZ5Z0C7161043
Logged
_nameless
Hero Member
*****

Karma: +369/-1644
Offline Offline

Posts: 2933



« Reply #1 on: April 11, 2018, 03:34:04 AM »

the read you posted is shit. you wont be pulling any info from variant a4 chassis cars with a clone vagtacho.
Logged

If you are broke or expecting free handouts DO NOT message me. I'll probably put you on blast if you do.
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #2 on: April 11, 2018, 08:06:55 AM »

Who says its a clone? Anyways, how SHOULD I read it via odb2 port? I can't get the eeprom flasher to communicate
Logged
_nameless
Hero Member
*****

Karma: +369/-1644
Offline Offline

Posts: 2933



« Reply #3 on: April 11, 2018, 08:18:51 AM »

Who says its a clone? Anyways, how SHOULD I read it via odb2 port? I can't get the eeprom flasher to communicate
because real tools dont have issues reading this cluster, clones do.  If you did youd have a original tool youd have factory support and not asking online form for help. Tongue
Logged

If you are broke or expecting free handouts DO NOT message me. I'll probably put you on blast if you do.
k0mpresd
Hero Member
*****

Karma: +146/-55
Offline Offline

Posts: 1656


« Reply #4 on: April 11, 2018, 09:18:02 AM »

eh, vagtacho sucks on any MM cluster. genuine or not.

i use carprog for audi/beetle mm cluster. 100% success.
Logged
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #5 on: April 11, 2018, 10:21:08 AM »

eh, vagtacho sucks on any MM cluster. genuine or not.

i use carprog for audi/beetle mm cluster. 100% success.

Thanks for legit help. Wouldnt happen to have an original dump in case mine is not recoverable would you?
Logged
k0mpresd
Hero Member
*****

Karma: +146/-55
Offline Offline

Posts: 1656


« Reply #6 on: April 14, 2018, 07:24:46 PM »

attached.
Logged
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #7 on: April 17, 2018, 03:05:38 AM »

attached.

Thanks! So is carprog the only way I should flash this (I dont have one yet) or do you think flashing with tacho might work?
Logged
miigotu
Jr. Member
**

Karma: +2/-1
Offline Offline

Posts: 36


« Reply #8 on: April 17, 2018, 03:28:54 AM »

I noticed thats a format match to the last 2048 bytes of my eep dump with tacho, ill see how it works out tomorrow if I cant get a proper 2048 only Ill add the garbage data to the top 2048 and try flashing that:

Code:
head -c2048 1C0920951J.eep > 1C0920951J_top_2048.eep
cat 1C0920951J_top_2048.eep 2002\ BEETLE\ TURBO\ S\ 1C0920951JX\ 117600KM.bin > 2002\ BEETLE\ TURBO\ S\ 1C0920951JX\ 117600KM.eep
vbindiff 1C0920951J.eep 2002\ BEETLE\ TURBO\ S\ 1C0920951JX\ 117600KM.eep
« Last Edit: April 17, 2018, 03:31:54 AM by miigotu » Logged
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.08 seconds with 19 queries. (Pretty URLs adds 0s, 0q)