Pages: 1 2 [3] 4 5
Author Topic: PID 2.7T Hybrid  (Read 22116 times)
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #30 on: October 06, 2019, 11:40:41 AM »

Your IMX is a mess during spool. Bring it down significantly. It should be flat until you reach desired boost

Thanks, gonna test it tomorrow.
But the spool is very weird, in my opinion. I attached another VCDS log (70% DC), that I've made before.


Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #31 on: October 06, 2019, 12:12:42 PM »

i see 2 probs here:
1 boost cannot be controlled after 6k
2 pid


get a pressure test wg lines. check for leaks, actuator rod moving etc. probably one of them faulty
check n75 in another car

log it with TVLDMX = 0 and ldrxn ~180
if you see boost goes high after 6k with  then probably wg hole should be ported

as second
did you flat KFLDRL? k03 wont work good with that
is it stock springs in actuators used?
cap DIMX @3k ~~~40%
raise Q2
play with Q1ST

N75 is new. I'm pretty sure it's because of PID. But it's because of the pressure can't be dropped down in a short period of time. Like a Chinese Turbo with restricted WG port.

The spool is not lineal at all. When DC is 95% it goes like
RPM  2100  2400 2800 3100 
Mbar 1300 1500 1900  2800

That's why N75 should start reducing DC from at least 2400RPM. This is my theory and I'm gonna check it tomorrow.
I've raised Q2 magnificently and brought Q0 and IMX down. I hope there will be no oscillations.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Online Online

Posts: 12232


WWW
« Reply #32 on: October 06, 2019, 10:02:10 PM »

Don't touch any of the Q params until you have an IMX that makes sense. You're wasting your time adjusting more than one thing at once.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #33 on: October 19, 2019, 07:14:12 AM »

Looks like I've found the problem) WG coudn't be fully open due to poor adjustment.  

But now I have another problem. I can't request more than 200% of rlsol and rlmax at middle RPM. The requested load goes down from 2000RPM until 4200RPM and then rises up again.


IRL/IOP are ok, LDRXN was set to 230%, KFLDHBN 2.55 KFPED 100%

What did I miss? Please give me a hint.
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #34 on: October 19, 2019, 07:16:47 AM »

KFLDHBN limiting you load, but that is good beacuse you expect 1.5 boost at red line with K04?
« Last Edit: October 19, 2019, 07:22:10 AM by BlackT » Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #35 on: October 19, 2019, 08:03:44 AM »

How can this be if I set KFLDHBN to 2.6?

1.5bar is for test only. PID is currently disabled. 
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #36 on: October 19, 2019, 08:26:57 AM »

How can this be if I set KFLDHBN to 2.6?

1.5bar is for test only. PID is currently disabled. 
you have to options, to read how ME7 convert load to boost and get answer to you question.
Or set that whole table to lets say 2.9-3.0 and dont think about it
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #37 on: October 19, 2019, 09:13:59 AM »

Thanx, I set up it to 3 and now rlsol is 205 and boost is about 1.4bar)
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #38 on: October 19, 2019, 10:42:47 AM »

I set 4 and the same load 205. I'm pretty sure there is another limit.
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #39 on: October 19, 2019, 11:08:11 AM »

Post log again
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #40 on: October 19, 2019, 01:18:40 PM »

Attached
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #41 on: October 19, 2019, 01:43:55 PM »

Now you get rid of ldrlts
But how your LDRXN values looks like?
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #42 on: October 19, 2019, 02:00:30 PM »

Here it is. Also I attached the files above.
Logged
terminator
Sr. Member
****

Karma: +15/-4
Offline Offline

Posts: 425


« Reply #43 on: October 19, 2019, 02:02:49 PM »

Please note, I set CWMDAPP to 8, so PID is disabled now.
Logged
BlackT
Hero Member
*****

Karma: +79/-39
Offline Offline

Posts: 1415



« Reply #44 on: October 19, 2019, 02:17:25 PM »

Maybe to high IAT or knock will give you smaller values to rlmax_w. I never goo too deep in that conversion rlmx to rlmax. 
Page 855 in FR maybe can give you a answer
Logged
Pages: 1 2 [3] 4 5
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.019 seconds with 17 queries. (Pretty URLs adds 0s, 0q)