|
terminator
|
 |
« Reply #45 on: October 19, 2019, 02:33:04 PM »
|
|
|
Maybe the reason is TCU from ABT? I did some 4z7 files with MT and never had any problem up to 2.0-2.1bar...
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #46 on: October 21, 2019, 01:33:23 PM »
|
|
|
No one knows? I've just tried to flash 551R instead of 551N and got the same problem.
LDRXN
KFMIRL/KFMIOP
KFLDHBN
Are there any other limits?
Is it possible that TCU limits RL?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #47 on: October 21, 2019, 02:20:16 PM »
|
|
|
Ditch CWMDAPP it may have load limit side effects I haven't traced.
Also log milsol and misopl1 if possible.
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #48 on: October 21, 2019, 05:00:53 PM »
|
|
|
I already set CWMDAPP to 0 but nothing changed. Now PID works just fine, but I can't control the requested boost. Also log milsol and misopl1 if possible.
Ok, I will, thanks. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #49 on: October 21, 2019, 05:02:09 PM »
|
|
|
I already set CWMDAPP to 0 but nothing changed. Now PID works just fine, but I can't control the requested boost.
Please post logs. |
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #50 on: October 22, 2019, 01:26:00 AM »
|
|
|
On ZF5HP I've only ever torque limiters in the RS6 gearbox.
But hey, read out your trans...
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #51 on: November 30, 2019, 10:20:43 AM »
|
|
|
I would like to start it from scratch.
I changed only KFLDRL and KFLDIMX. Other N75 maps are fully stock. Now specified and actual pressures are pretty close, but the turbos spool very slow and there are overshoots while gear shifting.
The question is how to make it spool faster? Should I raise IMX?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #52 on: November 30, 2019, 12:26:23 PM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #53 on: November 30, 2019, 01:10:46 PM »
|
|
|
Like this?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #54 on: November 30, 2019, 01:48:26 PM »
|
|
|
That makes very little sense.
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #55 on: November 30, 2019, 02:25:03 PM »
|
|
|
Would you please be more specific?  Please take a look. I changed the axis. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #56 on: November 30, 2019, 02:36:03 PM »
|
|
|
Why is it linear? Are you intending to use precontrol?
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #57 on: November 30, 2019, 03:03:41 PM »
|
|
|
Yes, I attached KFLDRL one more time.
And I have overshoots here.
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #58 on: November 30, 2019, 04:18:58 PM »
|
|
|
Something is very wrong, since drl isn't giving you even remotely the dc you need.
|
|
|
|
|
Logged
|
|
|
|
|
terminator
|
|
« Reply #59 on: November 30, 2019, 10:58:58 PM »
|
|
|
May I ask you, what is exactly wrong?
|
|
|
|
« Last Edit: December 01, 2019, 03:19:32 AM by terminator »
|
Logged
|
|
|
|
|
