Pages: 1 2 3 [4] 5 6 ... 21
Author Topic: Bosch EV14 Injector Migration  (Read 361492 times)
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #45 on: January 28, 2012, 06:27:40 PM »

nehalem,

Wouldn't it be more accurate to use the equation QSTAT * sqrt(4/3) rather than QSTAT * sqrt(58.00/43.50), being that what the equation is trying to achieve is that the initial psi is 75 percent of the target psi. I know the equation will work out the same, but 58 and 43.5 are rounded off where as 4 and 3 is exact... also making calculations easier?

Brett

PS... don't take this reply as a smart-ass one, I've been learning a ton off your posts!

Hi, No worries, this was one of my first attempts at mathematically calculating anything for this car.  I was quite nervous tbh.  lol

Did you mean to suggest sqrt (3 / 4)  because you'll find that sqrt(58.00/43.50)=sqrt(4/3)  ...
I believe sqrt (4/3) is correct though.
Logged
PovGRide742
Jr. Member
**

Karma: +4/-1
Offline Offline

Posts: 33


« Reply #46 on: January 29, 2012, 02:02:12 PM »

Hi, No worries, this was one of my first attempts at mathematically calculating anything for this car.  I was quite nervous tbh.  lol

Did you mean to suggest sqrt (3 / 4)  because you'll find that sqrt(58.00/43.50)=sqrt(4/3)  ...
I believe sqrt (4/3) is correct though.

Actually, I meant 4/3 over 58/43.5... and for this reason:
4bar = 58.XXXXXXXXpsi, and 3bar = 43.5XXXXXXXpsi, so if you did the math absolutely correct, it would equal exactly that, 4/3. So it's just easier to use the equation of 4/3 instead of the psi/psi. This way, there is no way to be 'mathematically' incorrect.
Logged
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #47 on: January 29, 2012, 10:21:30 PM »

sqrt(4/3) ~= 1.15470054
sqrt(58/43.5) ~= 1.15470054

Logged
PovGRide742
Jr. Member
**

Karma: +4/-1
Offline Offline

Posts: 33


« Reply #48 on: January 30, 2012, 06:08:26 AM »

sqrt(4/3) ~= 1.15470054
sqrt(58/43.5) ~= 1.15470054


Lol, yes... I know they equal the same number. In the odd event though, that you'd want to go ridiculously exponentially, 4/3 would be more accurate than 58/43.5. Although, to sum this up, I think you've already agreed 4/3 is easier.
Logged
Tony@NefMoto
Administrator
Hero Member
*****

Karma: +130/-4
Offline Offline

Posts: 1389


2001.5 Audi S4 Stage 3


« Reply #49 on: January 30, 2012, 03:04:27 PM »

Just remember that no matter how perfect your equations are, as soon as you have them running in your car, you end up changing them. Wink
Logged

Remember you have to log in if you want to see the file attachments!
Info or questions, please add to the wiki: http://www.nefariousmotorsports.com/wiki
Follow NefMoto developments on Twitter: http://twitter.com/nefmoto
PovGRide742
Jr. Member
**

Karma: +4/-1
Offline Offline

Posts: 33


« Reply #50 on: February 02, 2012, 05:59:27 AM »

Just remember that no matter how perfect your equations are, as soon as you have them running in your car, you end up changing them. Wink
Yeah, I know, I'm slightly OCD, so I like as-accurate-as-possible starting values.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #51 on: May 06, 2012, 11:40:27 PM »

Just migrated to EV14 750cc (72#) @ 3bar

I tweaked TVUB some starting with Tony's values. Car is running fine.... but i think i need to massage cold start fueling.

Anybody else have to do this?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Rick
Hero Member
*****

Karma: +62/-4
Offline Offline

Posts: 704


« Reply #52 on: May 07, 2012, 07:25:05 AM »

Never had an issue with cold start, but warm (not hot) start usually needs playing with.
Logged
julex
Hero Member
*****

Karma: +78/-4
Offline Offline

Posts: 923


« Reply #53 on: May 07, 2012, 07:51:12 AM »

Just migrated to EV14 750cc (72#) @ 3bar

I tweaked TVUB some starting with Tony's values. Car is running fine.... but i think i need to massage cold start fueling.

Anybody else have to do this?

Yes. I had to bump up warmup maps for fueling as I was going lean and engine was bogging down when stepped on for normal acceleration. This would only be the case for medium load. Either high load or barely any load requests would not cause that.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #54 on: May 08, 2012, 12:55:58 PM »

Assume this (http://www.boschdealer.com/specsheets/0280158117cs.jpg) to be accurate and we already know a 4-bar pressure regulator is 58.02 psi.  Therefore FNPW_OFFCOMP has a theoretical value of:  1.1852.

Using the same decimal accuracy as the calibration sheet:
1.1852 = 1.2179+(58.02-54.96)*(1.1638-1.2179)/(60.03-54.96)

In MATLAB I entered the FNPW_OFFSET values and fit a shape-preserving spline.
You can see the attached graph below to view the curve-fit.
Interpolated output from the curve below is naturally multiplied by 1.1852.

Volts    MS
7.04     3.865
10.07   1.678
12.04   1.227
14.08   0.926
17.88   0.779

Following up on this, i have a 3bar fpr

interpolating OFFCOMP gets me 1.1326 ..

nehalem, i dont have your non-comped spline interpolation, but if i divide by 1.1852, I get


Volts    ms (2.7bar)  ms (3bar)   ms (4bar)
 7.04    3.261           3.693         3.865          
10.07   1.416           1.604         1.678
12.04   1.035           1.173         1.227
14.08   0.781           0.884         0.926
17.88   0.657           0.744         0.779


Does this look right?
« Last Edit: May 08, 2012, 02:23:20 PM by nyet » Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #55 on: May 08, 2012, 02:14:33 PM »

Yes - That math looks correct.  However, after a while of adjusting LTFT's, I ended up with:
3.12   1.35   0.99   0.75   0.63

Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #56 on: May 08, 2012, 02:20:56 PM »

I don't get the whole LTFT tuning thing.

how can you do anything but adjust only 2 operating points of the bus voltage (i'm assuming ~14v out of the alternator, or regulated 12v during cranking)
« Last Edit: May 08, 2012, 06:10:42 PM by nyet » Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #57 on: May 08, 2012, 06:22:42 PM »

Precisely the way you stated it.  You need to make the assumption that your operation is not scalar, rather you are vector multiplying the entire table by your adjustment factor.  new_val = (1+x) * old_val      on the entire table as a vector in effect
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #58 on: July 02, 2012, 09:28:13 AM »

I've got the car's trims right, but i'm still having

1) cold start problems (possibly checkvalve related)
2) lumpy idle

Anybody else have idle issues?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #59 on: July 15, 2012, 02:47:39 PM »

update

I've got the car's trims right, but i'm still having
1) cold start problems (possibly checkvalve related)
Due to cold plugs. Investigating multi-spark

Quote
2) lumpy idle

Bad IOP. Reverted first two load rows to stock, and my idle problems went away.

Also, gave up on trim tuning. I'm back to the theoretical TVUB specs as posted in my earlier post, and I'm doing trim tuning with MAF/KRKTE tweaking.
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
Pages: 1 2 3 [4] 5 6 ... 21
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.068 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)