Pages: 1 2 3 [4] 5 6 ... 9
Author Topic: Ignition cut rev limiter me7  (Read 121771 times)
Jim_Coupe
Hero Member
*****

Karma: +16/-12
Offline Offline

Posts: 663



« Reply #45 on: February 15, 2017, 07:49:50 AM »

Hehehe lol Smiley
Logged

E85oholic
bobg
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 20


« Reply #46 on: February 19, 2017, 03:56:35 PM »

hey everyone,

Trying to get hard limiter working but i cant seem to find and xdf file with proper locations to make adjustments. I have 8e0909518f ecu. I cant find kfszt and kftsrl if just all 0. Please help much appreciated, this forum is amazing already got my boost where I want it and cars running great just need some pop pop bang bang  Grin.

thx
Logged
d0xx
Jr. Member
**

Karma: +12/-11
Offline Offline

Posts: 35


WWW
« Reply #47 on: February 22, 2017, 03:02:28 AM »

hey everyone,

Trying to get hard limiter working but i cant seem to find and xdf file with proper locations to make adjustments. I have 8e0909518f ecu. I cant find kfszt and kftsrl if just all 0. Please help much appreciated, this forum is amazing already got my boost where I want it and cars running great just need some pop pop bang bang  Grin.

thx

I dont know which SW you have, but if you have 1037363670 - your addresses are the following:
FTOMN @ 0x1A7BE, size 1x1, 8bit, factor 0,1*eprom
KFSZT  @ 0x1A892, size 8x8, 8bit, factor 0,1*eprom
KFTSRL @ 0x1A8E7, size 10x9, 8bit, factor 0,1*eprom

Attached a few screenshots and a .csv with map-data.
Logged

______________________________
www.ecu-codes.com
bobg
Newbie
*

Karma: +0/-2
Offline Offline

Posts: 20


« Reply #48 on: March 16, 2017, 08:43:35 AM »

thx for reply not sure how i would know sw. But i'm pretty sure ftmon for me is at 1a775 it shows 5. One xdf file i have shows at 1b2ac which is incorrect and where you said i think is incorrect also as it show up 0.
Logged
d0xx
Jr. Member
**

Karma: +12/-11
Offline Offline

Posts: 35


WWW
« Reply #49 on: March 24, 2017, 11:44:19 AM »

It would help to upload your file..
Logged

______________________________
www.ecu-codes.com
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #50 on: July 19, 2017, 08:47:30 PM »

Good evening guys !!!
I set my limiter to 7100 rpms, but the cut comes at 5800 rpms.
Could anyone give a hint how fasso it limit to 7100 rpms?
In this bin I have active AL / NLS.
Very grateful for any help.
Logged
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #51 on: July 19, 2017, 08:54:53 PM »

Ops! Xdf wrong.
I have set up the rpms columns of kftsrl as indicated in wik and here too. Best column kftsrl at 7100 and penutima at 7060rpm.
sorry.
Logged
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #52 on: July 20, 2017, 07:50:03 PM »

Same result.
Limiting to 5800 rpms.
How to reach 7100 rpms?
What am I leaving behind ??
Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #53 on: July 20, 2017, 11:19:19 PM »

What is NMAXOG set to?
Can you upload a screenshot of your new setup?
Logged
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #54 on: July 21, 2017, 03:19:39 PM »

Here is the capture screen.
a question.
I have not changed the axes of the kfzw maps.
Will this be my mistake?
In doubt, I will change everyone and see the result.
Thank you very much for your attention.
Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #55 on: July 21, 2017, 03:27:26 PM »

What about KFSZT?
Logged
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #56 on: July 21, 2017, 07:49:42 PM »

Had changed in another file with the same configuration of the kftsrl axes and with the whole column in 0.
But even so the cut came at 5800.
As in wik did not mention about kfszt I decided to leave original for a test.
When the first or second gear pulls off the bursts !!
More in a higher gear limits to the 5800.notei q is tied past the 5000 rpm. strange behavior.
It would not be the case to interpolate the kftsrl axis with a difference smaller than 4000 rpms to 7060 rpms.
Type per line of 6000 rpms in place of 4000 rpms?
I'm going to test that tomorrow.
 thank you
Logged
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #57 on: July 21, 2017, 08:49:17 PM »

I'm going to take a test with that.
Logged
cpp
Jr. Member
**

Karma: +3/-0
Offline Offline

Posts: 25



« Reply #58 on: July 22, 2017, 07:15:00 AM »

Same result.
Logged
KasperH
Hero Member
*****

Karma: +24/-8
Offline Offline

Posts: 632


« Reply #59 on: July 22, 2017, 07:55:05 AM »

Try setting fuel cut 100-200 RPM higher than spark cut Smiley
Logged
Pages: 1 2 3 [4] 5 6 ... 9
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.033 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)