Pages: 1 ... 46 47 [48] 49 50 ... 63
Author Topic: ME7 EEPROM programmer  (Read 842980 times)
QuickS4
Full Member
***

Karma: +6/-6
Offline Offline

Posts: 72


« Reply #705 on: February 11, 2018, 06:55:07 AM »

In case this helps someone else out:

I was having all kinds of errors when trying to read over OBD. I went into the advanced COM port settings in device manager and set the latency to 2ms.

After that it worked without errors! Good luck!
Could you post what cable you were using for other's to recognize.

Nice tweak btw.

Sent from my Pixel XL using Tapatalk

Logged
StokeR
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #706 on: February 21, 2018, 05:57:23 AM »

Does anybody has the correct wiring, pinout for Alfa Romeo 147 1.6 ME7.3.1 ECU?

Is it
15, 16, 32, 47, 48 +12V
53 K-Line
20 and Box 0V Huh

Can't get it working with a blue standard KKL interface.
Logged
StokeR
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #707 on: February 21, 2018, 12:29:17 PM »

What does this error mean?

Code:
C:\ME7EEPROM>ME7EEPROM --OBD -p 3 -b 10400 -r 95040.bin
ME7_EEPROM v1.40
COM: 3, Baud Rate: 10400
Opening COM3 ... OK
Initiating communication ... FAIL. (error=0x21007)
Closing COM3

C:\ME7EEPROM>
Logged
StokeR
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #708 on: February 21, 2018, 01:21:32 PM »

Code:
C:\ME7EEPROM>ME7EEPROM --bootmode 95040 --CSpin P4.7 -p 3 -b 10400 -r 95040.bin
ME7_EEPROM v1.40
COM: 3, Baud Rate: 10400
Memory type: 95040, size: 512
Chip Select pin: P4.7
Opening COM3 ... OK
Starting Boot_mode ... FAIL ... No ECU response. (error=0x20F07)
Closing COM3
Logged
marcjero
Full Member
***

Karma: +4/-0
Offline Offline

Posts: 58


« Reply #709 on: February 23, 2018, 06:56:53 AM »

Hi,
Galletto includes a software able to read eeprom in boot mode. Unfortunately immobilizer data are obfuscated. Is this program similar of does it work much better ?

Envoyé de mon Nexus 4 en utilisant Tapatalk

Logged
TRespect
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 72


« Reply #710 on: February 27, 2018, 04:16:31 AM »

Hi,

sorry to hijack and double-post but I'm a bit stuck here. I tried to program keys on my touareg (2004 v6) and the procedure somewhat failed and ended up with a dead cluster, no ignition no lights no odb communication. I did get the skc pin code from the toureg before the vcds key matching procedure. I have the eeprom dump. will restoring the eeprom dump restore the original key matching or is the key matching info in a separate module (the immobilizer)? it it is in the immo module is there a method or tool (hardware or software) to communicate with it.
my thred is here if you guys can help:
http://nefariousmotorsports.com/forum/index.php?topic=13927.0title=
Logged
TRespect
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 72


« Reply #711 on: March 01, 2018, 04:00:04 AM »

problem solved. I'm still trying to understand what happened and how to avoid it in the future. so if you have any ideas please head over to my thread :-)
Logged
tao13
Sr. Member
****

Karma: +16/-46
Offline Offline

Posts: 460


« Reply #712 on: March 13, 2018, 01:50:42 PM »

Hi
If i try on the car tool works to read epprom!
I tried to use it with my ECU on  Bench and communication failed!
The problem can be the instrument is not connected on "ecu bench" or if my ecu has immo ON?

Thanks
Logged
StokeR
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 9


« Reply #713 on: March 13, 2018, 02:21:04 PM »

I think its a problem with your wiring on bench, please double check.
Had the same problem.
Logged
EuroXs4
Full Member
***

Karma: +15/-31
Offline Offline

Posts: 209


« Reply #714 on: March 14, 2018, 06:16:45 PM »

Having a problem reading a ME7.5 ecu on the bench.Keeping getting error=0x07 any ideas??Trying to read via obd.Same error everytime.Using a 12vdc power supply rated at 2Amps.
Logged
tao13
Sr. Member
****

Karma: +16/-46
Offline Offline

Posts: 460


« Reply #715 on: March 21, 2018, 12:44:29 PM »

i checked the cable , they are ok , i tried to read eeprom and tried to use galleto (it stop on 80% like i try to read on car directly but with immo on)
Logged
Gallo75
Newbie
*

Karma: +0/-3
Offline Offline

Posts: 12


« Reply #716 on: June 26, 2018, 11:32:14 PM »

..
« Last Edit: June 27, 2018, 09:18:02 PM by Gallo75 » Logged

xdf files happen when mommy and daddy love each other very very much
Gallo75
Newbie
*

Karma: +0/-3
Offline Offline

Posts: 12


« Reply #717 on: June 27, 2018, 02:46:29 PM »

-p 1 --bootmode 95040 --CSpin P6.3 -r file did the trick.

Got a 512bytes file, all the info is ok, i was able to immo off and write it back.

EEPROM Status:
- VIN: WAUJT68E73A290473 (Audi 2003 - A4 01-08, Ingolstadt, Germany)
- SKC: 03521
- Immobiliser: Off
- Checksum: Ok
- Size: 512bytes
- Cluster Code: 15 93 37 84 45 D2
- P0601 DTC: not set
- Immo ID: AUZ6Z0B0352115
- Softcoding ID: 16581

engine started fine, but, any reason why the hazzard lights won't stop blinking?
« Last Edit: June 27, 2018, 09:19:46 PM by Gallo75 » Logged

xdf files happen when mommy and daddy love each other very very much
wolfe2118
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 14


« Reply #718 on: June 29, 2018, 11:49:23 AM »

I managed to read the file but now this is what I end up with when I try to write, anyone have any idea what I'm doing wrong?


C:\Users\jwolfe>C:\me7_95040.exe --bootmode -w -p 4 eeprom.bin
Ver: 1.31
Com Port: 4
Baud Rate: 10400
Opening COM4 ... OK
Starting Boot_mode ... uC identification response = 0xC5 (C167 derivatives) ... OK
Sending Loader + MonitorCore ... MonitorCore successfully launched
Initializing registers ... FAIL. (error=0x01)
Closing COM4

Thanks
Logged
c0llider
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 1


« Reply #719 on: June 30, 2018, 02:00:16 PM »

-p 1 --bootmode 95040 --CSpin P6.3 -r file did the trick.

Got a 512bytes file, all the info is ok, i was able to immo off and write it back.

EEPROM Status:
- VIN: WAUJT68E73A290473 (Audi 2003 - A4 01-08, Ingolstadt, Germany)
- SKC: 03521
- Immobiliser: Off
- Checksum: Ok
- Size: 512bytes
- Cluster Code: 15 93 37 84 45 D2
- P0601 DTC: not set
- Immo ID: AUZ6Z0B0352115
- Softcoding ID: 16581

engine started fine, but, any reason why the hazzard lights won't stop blinking?


If you unplug the ECU, does your Cluster say SAFE and hazard blinking?
Why immo off, did you loose keys or put different ECU?
Usually in those cars Hazards will be on if Key isn't programmed to cluster...
Logged
Pages: 1 ... 46 47 [48] 49 50 ... 63
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.025 seconds with 17 queries. (Pretty URLs adds 0s, 0q)