Pages: 1 ... 14 15 [16] 17 18 ... 23
Author Topic: DSG DQ250 Tuning  (Read 163831 times)
tuningfreak
Newbie
*

Karma: +9/-5
Offline Offline

Posts: 18


« Reply #225 on: July 27, 2020, 02:43:24 AM »

Hello guys, as you know dq500 and dq250mqb has boosted launch feature and some tuners can make this feature to the older dq250 versions.

Here is the example video :   https://youtu.be/jsUEcDTKf_4

Is anyone have experience about it? which maps should we touch?


Best Regards
Logged
teobolo
Full Member
***

Karma: +24/-6
Offline Offline

Posts: 112


« Reply #226 on: July 27, 2020, 05:02:54 AM »

mate did you look previous posts?or just post what you need for .

As i write on that topic almost none have manage to make it (only TVS )
Logged
birchbark506
Sr. Member
****

Karma: +11/-11
Offline Offline

Posts: 414


« Reply #227 on: August 07, 2020, 07:42:11 PM »

KusLaunchNAbMax_ko

do you know what address that would be. my a2l dose not have that map
Logged
mantasos
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 8


« Reply #228 on: September 30, 2020, 12:39:00 AM »

mate did you look previous posts?or just post what you need for .

As i write on that topic almost none have manage to make it (only TVS )

Haven't tried it but, i believe that you can implement hard launch control on ecu like you would for a manual but having break switch & full throttle instead of clutch switch.  set to 200-300rpm lower than dsg launch control threshold.

i mean, if im thinking right, it will never get to dsg lc rpm so it will never cut throttle and the engine's ecu hard launch control will be enabled  Grin
« Last Edit: September 30, 2020, 12:43:25 AM by mantasos » Logged
FlyboyS4
Full Member
***

Karma: +20/-1
Offline Offline

Posts: 215


WWW
« Reply #229 on: October 18, 2020, 06:28:02 PM »

Have any of you used HP Tuners software for tuning the DQ250?

Some screen shots of the interface

http://mygolfmk7.com/knowledgebase/hp-tuner-suite-screenshots/

There's little guidance on the HP Tuners site and the software appears to be limited to providing brief descriptions of the variables.
Logged
newai
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 2


« Reply #230 on: October 27, 2020, 09:58:48 PM »

Hi everyone! Please help enable launch control on DSG250.
Logged
gman86
Hero Member
*****

Karma: +45/-128
Offline Offline

Posts: 705


« Reply #231 on: October 27, 2020, 11:46:26 PM »

Hi everyone! Please help enable launch control on DSG250.

Sure! How about we do your engine too? For completeness.
Logged
newai
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 2


« Reply #232 on: October 28, 2020, 09:46:06 PM »

Sure! How about we do your engine too? For completeness.

Thanks, but I have 225 hp and 480 nm. And now the problem is in a good start. I deal with DSG myself with the help of this forum. But I can't figure out how to turn on the launch control.
Logged
birchbark506
Sr. Member
****

Karma: +11/-11
Offline Offline

Posts: 414


« Reply #233 on: January 23, 2021, 07:49:41 AM »

anyone got anything for the DQ250 MQB i been using the Exx full damos but there a few maps that seem to be missing for the MQB dq250
Logged
marchewa
Full Member
***

Karma: +3/-0
Offline Offline

Posts: 53


« Reply #234 on: May 05, 2021, 03:03:13 AM »

DSG DQ250 reverse light signal


Old dq250 (eg. in audi tt 1gen) had direct reverse gear signal on pin 12 while newer gearboxes are not using this pin. I have newer DSG (02E300014H 069D61902ec__getriebe_DSG_chD6 F31S) and would like to ask if is it  possible to activate this signal in software? I need it as this gearbox will be working in older chassis.
dsg readout attached
Logged
Leonhard
Full Member
***

Karma: +27/-2
Offline Offline

Posts: 112


« Reply #235 on: May 05, 2021, 12:44:10 PM »

check this one:

3191B 1x1 8Bit
Id: SbeEnableRFL_ko
"Ausgabe Rückfahrlicht ein-/ausschalten"
Logged
marchewa
Full Member
***

Karma: +3/-0
Offline Offline

Posts: 53


« Reply #236 on: May 07, 2021, 12:00:41 AM »

Thanks Leonhard, I set to 1 but it is not working and still constant +3V on pin 12.
Logged
Leonhard
Full Member
***

Karma: +27/-2
Offline Offline

Posts: 112


« Reply #237 on: May 09, 2021, 03:48:42 AM »

Ok, too bad, but that's all I got  Undecided
Logged
jochen_145
Full Member
***

Karma: +9/-4
Offline Offline

Posts: 177


« Reply #238 on: May 09, 2021, 09:42:56 AM »

Thanks Leonhard, I set to 1 but it is not working and still constant +3V on pin 12.

Witch way did you check ?

T20a/12 should be a low-side-switch AFAIR..
Logged
kepsus
Newbie
*

Karma: +0/-1
Offline Offline

Posts: 7


« Reply #239 on: July 14, 2021, 11:53:11 AM »

Now my DQ250 is not in a vag car, but i still have med 9.1 ecu.  Would it possible to code the dq250 to have launch , even that i dont have any ESP /ABS
Logged
Pages: 1 ... 14 15 [16] 17 18 ... 23
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.025 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)