Pages: [1] 2 3 ... 21
Author Topic: Bosch EV14 Injector Migration  (Read 361528 times)
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« on: December 24, 2010, 05:00:48 PM »

Has anyone self-installed a set of EV14's and got the car to a decent state of tune?

What hardware and software did you use?

Is there a Master List of Table Names in the standard B5 S4 M-box?


Happy Holidays!
Logged
wickster
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 26


« Reply #1 on: December 29, 2010, 12:36:13 PM »

I plan to use these injectors as well so I'm also curious. Are you using 550s or 750s? Stock 4 bar FPR and 85mm hitachi MAF?
Logged

'01.5 Audi S4 2.7T - 6MT - K04s - ASP 85mm Hitachi - 49lb Delphi
s5fourdoor
Hero Member
*****

Karma: +33/-3
Offline Offline

Posts: 617


« Reply #2 on: December 29, 2010, 08:06:33 PM »

Hey - Spot on.  I want to run Tony's base file m-box with a 85mm MAF.  On top of that I want to run the stock FPR, a Bosch 044 pump, and Bosch EV14 550cc injectors.  This combination seems like the best overall setup to me, given what I understand about the quality of the parts.
Logged
nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #3 on: January 19, 2011, 05:04:42 PM »

Hey - Spot on.  I want to run Tony's base file m-box with a 85mm MAF.  On top of that I want to run the stock FPR, a Bosch 044 pump, and Bosch EV14 550cc injectors.  This combination seems like the best overall setup to me, given what I understand about the quality of the parts.

Does anybody have the Bosch part numbers that people are using for this application?

For reference:

http://www.usrallyteam.com/content/products/injector/Bosch_Injector_data.xls

The closest thing I can find is 0 280 158 117/118 (532cc at 2.7bar, 550cc/52# at 3bar)

ETA:

The 118 variant has 22deg dual cone and the spray pattern is canted (like stock), but it is only 347cc at 3 bar.
There is also the 0 280 158 123 variant (627cc/60# at 3bar) which has a EV1 (Jetronic) connector... and the connector offset by 90%

http://nyet.org/cars/info/BoschMotorsportsInjectors.pdf

Here is what  I have so far

http://s4wiki.com/wiki/Fuel_injectors

Latencies:
http://nyet.org/cars/info/ev14-latency/



« Last Edit: July 22, 2013, 12:26:35 PM by nyet » Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
paracaidista2.7T
Newbie
*

Karma: +6/-0
Offline Offline

Posts: 21


« Reply #4 on: January 25, 2011, 04:40:30 PM »

Has anyone self-installed a set of EV14's and got the car to a decent state of tune?

What hardware and software did you use?

Is there a Master List of Table Names in the standard B5 S4 M-box?


Happy Holidays!


I got my car (2001 A6 2.7T) running fine with them. I am using a 90mm MAF housing, 52# EV14 injectors (0 280 158 117/118)@4bar, PJK04s, 2.8L heads. It wasn't any harder than 630 Seimens at 3bar. I just had to tweak the file slightly, they ran a bit leaner at WOT than the Seimens did.
Logged
wickster
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 26


« Reply #5 on: January 31, 2011, 06:19:40 PM »

What all did you tweak to get them to run well? Just KRKTE or something else?
Logged

'01.5 Audi S4 2.7T - 6MT - K04s - ASP 85mm Hitachi - 49lb Delphi
paracaidista2.7T
Newbie
*

Karma: +6/-0
Offline Offline

Posts: 21


« Reply #6 on: February 02, 2011, 08:13:52 AM »

I refined my KRKTE so that lambda requested jives with wideband actual (it was slightly lean compared to the Seimens). I also set KFKHFM to 1 across the board, logged about 100 miles of driving under varied conditions, and then used that data to refine KFKHFM (this usually takes a few repetitions). I am not certain that I needed to do the KFKHFM step, but it has become habit when I am experimenting. I like to have LTFTs around -3 or so, since when I am logging the fuel I use is of known quality.
Logged
wickster
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 26


« Reply #7 on: February 02, 2011, 02:13:17 PM »

http://www.injectordynamics.com/
Paul from Injector Dynamics has given me the following data.

The volumetric flow rate on gasoline at 125F is 628cc/min.

The battery comp/dead time/offset/latency/lag is as follows:

Units are volts and microseconds.

8 - 2500
9 - 1940
10 - 1520
11 - 1270
12 - 1100
13 - 935
14 - 800
15 - 690
16 - 600

Logged

'01.5 Audi S4 2.7T - 6MT - K04s - ASP 85mm Hitachi - 49lb Delphi
wickster
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 26


« Reply #8 on: February 07, 2011, 11:33:08 PM »

I tested these values with excellent results thus far.
Logged

'01.5 Audi S4 2.7T - 6MT - K04s - ASP 85mm Hitachi - 49lb Delphi
wickster
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 26


« Reply #9 on: February 10, 2011, 08:55:42 PM »

What KRKTE value is everyone using with the Bosch EV14 550s?
Logged

'01.5 Audi S4 2.7T - 6MT - K04s - ASP 85mm Hitachi - 49lb Delphi
julex
Hero Member
*****

Karma: +78/-4
Offline Offline

Posts: 923


« Reply #10 on: February 22, 2011, 02:28:59 PM »

http://www.injectordynamics.com/
Paul from Injector Dynamics has given me the following data.

The volumetric flow rate on gasoline at 125F is 628cc/min.

The battery comp/dead time/offset/latency/lag is as follows:

Units are volts and microseconds.

8 - 2500
9 - 1940
10 - 1520
11 - 1270
12 - 1100
13 - 935
14 - 800
15 - 690
16 - 600



Albeit it looks about right, unfortunately is proper but only for 2.7bar fuel pressure which is what everyone tests injectors at...

Check this:

http://www.boschdealer.com/specsheets/0280158117cs.jpg

What's important on this spreadsheet is FNPW_OFFCOMP table which tells you how much you need to multiply each dead time at its voltage to get real value for the FPR you're running.

Vast majority of people need to use 60.03 (for 4bar FPR) value and multiply the original FNPW_OFFSET (pretty close to values you listed) byt the multiplier.

Here is a catch. The table has errors, I think, since values for 30.02 and 60.03 since they don't follow data pattern. Check other injector calibration sheets on the site, I am fairly sure this to be true... anyway, 30.02 should have 0.8564 and 60.03 1.2638

I tried tuning with the base values but was getting really strange O2 corrections for idle/part throttle with things getting more in-line as the injector on time was getting longer indicating that the injector lag was smaller and smaller in respect to on-time. I am running 1000cc ev14 injectors so any timing discrepancy like that gets exaggerated on my set up. I plugged modified (for 3bar FPR I have) values and now I am dead on with corrections.
Logged
wickster
Jr. Member
**

Karma: +2/-0
Offline Offline

Posts: 26


« Reply #11 on: March 08, 2011, 03:28:51 PM »

What value would you use for 4 bar FPR or 60.03 multiplier?
1.220-1.250 looks about right.
Logged

'01.5 Audi S4 2.7T - 6MT - K04s - ASP 85mm Hitachi - 49lb Delphi
s4rmm
Jr. Member
**

Karma: +4/-1
Offline Offline

Posts: 28


« Reply #12 on: March 31, 2011, 01:57:29 AM »

So the EV14 injectors are a lot "slower" than Dekas?
Latency/lag at 14v should be 0.8ms * 1.25 = 1ms for 4bar FPR according to info posted in this thread?

Tony's file uses 0.4187ms for Dekas, I've seen others around 0.55-0.6ms @14v
Logged
NOTORIOUS VR
Administrator
Hero Member
*****

Karma: +58/-7
Offline Offline

Posts: 1056


« Reply #13 on: March 31, 2011, 02:40:58 PM »

I'm going to be buying ID 1000cc injectors... I wonder how well ME7 will cope  Grin
Logged

SCHNELL ENGINEERING BLOG ·  STANDALONE ECUS · TUNING · DYNO · WIRING · PARTS · VEMS
Google Talk: NOTORIOUS.VR
n00bs start here: http://s4wiki.com/wiki/Tuning
julex
Hero Member
*****

Karma: +78/-4
Offline Offline

Posts: 923


« Reply #14 on: April 01, 2011, 07:38:30 AM »

So the EV14 injectors are a lot "slower" than Dekas?
Latency/lag at 14v should be 0.8ms * 1.25 = 1ms for 4bar FPR according to info posted in this thread?

Tony's file uses 0.4187ms for Dekas, I've seen others around 0.55-0.6ms @14v

Since you asked:
http://siemensdeka.com/specsheets/FI114191.jpg
http://siemensdeka.com/specsheets/FI114961cs.jpg

This should clarify Smiley. Sounds like 0.5ms @ 14v should do the trick (FNPW_OFFSET 0.409 * FNPW_OFFCOMP 1.23)
Logged
Pages: [1] 2 3 ... 21
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.05 seconds with 17 queries. (Pretty URLs adds 0s, 0q)