Pages: 1 ... 31 32 [33] 34 35 ... 52
Author Topic: Nefmoto community project: Stage1 1.8t ME7.5 A4 (8E0909518AK-0003)  (Read 502517 times)
wayne
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 22


« Reply #480 on: March 25, 2015, 05:52:07 PM »

Hi everyone,

I had a look at the tune on 1st post and I'm a bit surprised with the LDRXN map. It is higher than the BAM map at peak boost and lower than a basic AUQ after 4k rpm. Is it because you are tuning on a k03 turbo and k03s, to run more timing advance or I'm completely out ?

I'm currently tunning a stage 1 tune (safe 91US/95 europe octane) on mine and then, since I have a lot of e85 station around (85% ethanol) pushing it with exclusive e85 tune. Would this be the appropriate place to post the stage 1 e85 tune ?

Logged
thelastleroy
Sr. Member
****

Karma: +19/-2
Offline Offline

Posts: 260



« Reply #481 on: March 26, 2015, 03:34:26 PM »

The boost curve was worked out to more or less top out the k03 on a AMB engine. It tapers off to maintain proper AFR in the high rpm range.  IDC was a factor.
Logged
ktm733
Hero Member
*****

Karma: +18/-8
Offline Offline

Posts: 660



« Reply #482 on: March 27, 2015, 01:40:30 PM »

I'm with him. I did a e85 tuning and I think it would be a good informational post on it. Then again this might belong in the stage 2 post as injectors are needed.
Logged
thefullmontee
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #483 on: April 07, 2015, 09:21:17 PM »

Are the current files on the first OP updated and correct for a stage 1 tune?
Ready to flash over?
Logged
TLS
Full Member
***

Karma: +1/-0
Offline Offline

Posts: 62


« Reply #484 on: April 07, 2015, 09:41:37 PM »

I'm guessing that since this is supposed to be a tutorial (once cleaned up a bit) and not a hand-out, if you can't answer that question, then you probably should not flash them to your car.

Or just do it and see what happens.
Logged
thefullmontee
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #485 on: April 07, 2015, 09:45:24 PM »

No need to be rude, question was simple. Just wondering if all the info is put back to the OP. I was assuming so since it showed a recent update this month. Ive been reading through it all. Ty tho
Logged
thefullmontee
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 6


« Reply #486 on: April 07, 2015, 09:46:18 PM »

Im using it a guide/tutorial just as intended. I plan on contributing as much as i can as i learn also
Logged
seany260
Full Member
***

Karma: +0/-1
Offline Offline

Posts: 119


« Reply #487 on: April 16, 2015, 11:30:53 PM »

Does anyone know the reason why MSLUB table in the v7 tuned file at the start of this thread has been modified from the stock file?
I'd just like to bring this to attention as I've had problems with trying to disable SAI using the most popular method of zeroing CDSLS/CWKONABG but did not work, instead I had to zero MSLUB/MSLBAS.
I've yet to test on stock values..
   
Logged
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #488 on: April 16, 2015, 11:46:46 PM »

Does anyone know the reason why MSLUB table in the v7 tuned file at the start of this thread has been modified from the stock file?
I'd just like to bring this to attention as I've had problems with trying to disable SAI using the most popular method of zeroing CDSLS/CWKONABG but did not work, instead I had to zero MSLUB/MSLBAS.
I've yet to test on stock values..
   

If it didn't work, the addresses were wrong.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
seany260
Full Member
***

Karma: +0/-1
Offline Offline

Posts: 119


« Reply #489 on: April 16, 2015, 11:52:12 PM »

If it didn't work, the addresses were wrong.
THIS IS WHAT I USED
CDSLS -181BO- '01 TO 00'
CWKONABG- 181B8 '05 TO 00'
Logged
seany260
Full Member
***

Karma: +0/-1
Offline Offline

Posts: 119


« Reply #490 on: April 17, 2015, 12:04:43 AM »

Does anyone know the reason why MSLUB table in the v7 tuned file at the start of this thread has been modified from the stock file?
I'd just like to bring this to attention as I've had problems with trying to disable SAI using the most popular method of zeroing CDSLS/CWKONABG but did not work, instead I had to zero MSLUB/MSLBAS.
I've yet to test on stock values..
   

sorry maybe Im confusing things as usual, let me get this clear, I should not say that SAI disable did not work by zeroing CDSLS/CWKONABG as it was disabled and did not throw any DTC'S. My issue was that the cold start strategy with increased rpms stopped functioning when i used this method.
Logged
masterj
Hero Member
*****

Karma: +61/-5
Offline Offline

Posts: 1049



WWW
« Reply #491 on: April 26, 2015, 10:45:57 PM »

sorry maybe Im confusing things as usual, let me get this clear, I should not say that SAI disable did not work by zeroing CDSLS/CWKONABG as it was disabled and did not throw any DTC'S. My issue was that the cold start strategy with increased rpms stopped functioning when i used this method.

That is expected. With cwkonabg you also disabling cat
Logged

nyet
Administrator
Hero Member
*****

Karma: +604/-166
Offline Offline

Posts: 12232


WWW
« Reply #492 on: April 26, 2015, 10:49:20 PM »

That is expected. With cwkonabg you also disabling cat

Does the s4wiki entry need some work?
Logged

ME7.1 tuning guide (READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
ddillenger
Hero Member
*****

Karma: +637/-21
Offline Offline

Posts: 5640


« Reply #493 on: April 27, 2015, 12:31:33 AM »

Does the s4wiki entry need some work?

If you want to preserve that whatnot, set it to 01.
Logged

Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!

Email/Google chat:
DDillenger84(at)gmail(dot)com

Email>PM
MadCow
Full Member
***

Karma: +2/-1
Offline Offline

Posts: 108


« Reply #494 on: April 27, 2015, 04:26:35 PM »

Does anyone know the reason why MSLUB table in the v7 tuned file at the start of this thread has been modified from the stock file?
   

I noticed that too, the actual numbers are barely different (identical up to 2 or 3 decimal places) so my guess is they all got raise/lowered by one bit somehow. I wouldn't worry about it.
Logged
Pages: 1 ... 31 32 [33] 34 35 ... 52
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.064 seconds with 18 queries. (Pretty URLs adds 0.001s, 0q)