Overrun Flames, Gargle, Pop

Pages: 1 ... 41 42 [43]

« previous next »

Author

Topic: Overrun Flames, Gargle, Pop (Read 396635 times)

agron25

Full Member

Karma: +1/-19
Offline

Offline

Posts: 65

	Re: Overrun Flames, Gargle, Pop « Reply #630 on: April 11, 2023, 01:05:13 PM »

thanks


	Logged

agron25

Full Member

Karma: +1/-19
Offline

Offline

Posts: 65

	Re: Overrun Flames, Gargle, Pop « Reply #631 on: May 28, 2023, 07:44:15 AM »

hello
I am looking for the address for DNWEK
audi RS3 8P 0261S02825
thanks


	Logged

amin70

Newbie

Karma: +0/-0
Offline

Offline

Posts: 1

	Re: Overrun Flames, Gargle, Pop « Reply #632 on: June 17, 2023, 09:20:56 AM »

Don't need to touch KFZW and KFZWOP to do a pop
touch only KFZWM all maps
KFTVSA KFTVSAKAT KFTVSAGRL KFTVSAGNG2


	Logged

ddaniel987

Newbie

Karma: +1/-0
Offline

Offline

Posts: 6

	Re: Overrun Flames, Gargle, Pop « Reply #633 on: May 02, 2024, 05:27:35 PM »

Hi guys, made it pop really good on overrun but I get 0 pops whatsoever when revving in standstill or in neutral. I read here i need to edit TVSAG0 but its not in my damos and can't find it..
Can someone please help me find TVSAG0 and CWSAWE? Thanks in advance
ME7.5 8N0906018AB 0002


	Logged

TeknoFi

Full Member

Karma: +1/-3
Offline

Offline

Posts: 85

	Re: Overrun Flames, Gargle, Pop « Reply #634 on: May 03, 2024, 07:59:43 AM »

Quote from: ddaniel987 on May 02, 2024, 05:27:35 PM

CWSAWE
Address (Hex) 0x11211
Size 1 Byte (8 Bit)
Output type: Floating point
Signed: No
LSB First: No

03 = Delay always active, no fuel cutoff during NOx-catalyst regeneration
02 = Delay activated only when clutch depressed, no fuel cutoff during NOx-catalyst regeneration
01 = Delay always active
00 = Delay active only when clutch depressed

No TVSAG0 as its 512kb.


	Logged

ddaniel987

Newbie

Karma: +1/-0
Offline

Offline

Posts: 6

	Re: Overrun Flames, Gargle, Pop « Reply #635 on: May 03, 2024, 10:06:44 AM »

Thank you, u a legend!! How do I make it pop on neutral when I dont have TVSAG0 in my firmware?


	Logged

akitossgti

Newbie

Karma: +0/-0
Offline

Offline

Posts: 7

	Re: Overrun Flames, Gargle, Pop « Reply #636 on: July 16, 2024, 10:37:34 PM »

Continuing with the thread of this post which is very interesting, could someone explain to me how it works in itself dnwek I attached a photo of funktionsrahmen me17.5 but I suppose that for many me17 will be worth it


	Logged

soykii

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: Overrun Flames, Gargle, Pop « Reply #637 on: July 26, 2024, 05:57:40 PM »

Hello Guys i have a problem with a med9.1.2 ecu i hope someone can help me or guide me to the right direction
I tryed to activate pop and bangs over the A/C button for this i changed
DNWEK to 8000rpm
Kftvsa/kftvsagi all to zero
KFZWM all maps in the low load to -25 from 6000rpm to 2500rpm
It pop and bangs really loud when i let the Pedal in the range 4000-6000rpm but around 3800rpm its stops but i can see in the cluster fuel is added the car accelerates slowly. When i push the AC button the car brakes i can feel it.
I logged the values and there i can see the timing jumps from negative to positiv and the pops are over.
When i push the button for example at 3000rpm and activate the AC it bangs for a few seconds after this i must push the button for the next time to make it this pop an bangs.
I hope someone can help


	Logged

Somebody

Newbie

Karma: +0/-0
Offline

Offline

Posts: 13

	Re: Overrun Flames, Gargle, Pop « Reply #638 on: August 21, 2024, 06:04:28 PM »

Just discovered this special thread about the topic.

Tried to find and modify the following maps:

CWSAWE - 158A9
KFZWMN - 137B8
KFZWMNST - 13896
KFTVSA - 196FE
KFTVSAKAT - not exist in this firmware
DNWEK - 158AF
KFZW - 0x164C1
KFZWOP - 0x15B85
KFZWOP2 - 0x15C35

Can someone take a look at this and confirm that I have found the right maps? (and have made the correct changes)

I haven't tested it on the vehicle yet.

Thanks


	Logged

Pages: 1 ... 41 42 [43]

« previous next »

Jump to:

Navigation

Personal Tools

November 25, 2024, 09:13:59 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search