agron25
Full Member
Karma: +1/-19
 Offline
Posts: 65
|
 |
« Reply #630 on: April 11, 2023, 01:05:13 PM »
|
|
|
thanks
|
|
|
|
|
Logged
|
|
|
|
agron25
Full Member
Karma: +1/-19
Offline
Posts: 65
|
|
« Reply #631 on: May 28, 2023, 07:44:15 AM »
|
|
|
hello
I am looking for the address for DNWEK
audi RS3 8P 0261S02825
thanks
|
|
|
|
|
Logged
|
|
|
|
amin70
Newbie
Karma: +0/-0
Offline
Posts: 1
|
|
« Reply #632 on: June 17, 2023, 09:20:56 AM »
|
|
|
Don't need to touch KFZW and KFZWOP to do a pop
touch only KFZWM all maps
KFTVSA KFTVSAKAT KFTVSAGRL KFTVSAGNG2
|
|
|
|
|
Logged
|
|
|
|
ddaniel987
Newbie
Karma: +1/-0
Offline
Posts: 6
|
|
« Reply #633 on: May 02, 2024, 05:27:35 PM »
|
|
|
Hi guys, made it pop really good on overrun but I get 0 pops whatsoever when revving in standstill or in neutral. I read here i need to edit TVSAG0 but its not in my damos and can't find it..
Can someone please help me find TVSAG0 and CWSAWE? Thanks in advance
ME7.5 8N0906018AB 0002
|
|
|
|
|
Logged
|
|
|
|
TeknoFi
Full Member
Karma: +1/-3
Offline
Posts: 85
|
|
« Reply #634 on: May 03, 2024, 07:59:43 AM »
|
|
|
Hi guys, made it pop really good on overrun but I get 0 pops whatsoever when revving in standstill or in neutral. I read here i need to edit TVSAG0 but its not in my damos and can't find it..
Can someone please help me find TVSAG0 and CWSAWE? Thanks in advance
ME7.5 8N0906018AB 0002
CWSAWE Address (Hex) 0x11211 Size 1 Byte (8 Bit) Output type: Floating point Signed: No LSB First: No 03 = Delay always active, no fuel cutoff during NOx-catalyst regeneration 02 = Delay activated only when clutch depressed, no fuel cutoff during NOx-catalyst regeneration 01 = Delay always active 00 = Delay active only when clutch depressed No TVSAG0 as its 512kb. |
|
|
|
|
Logged
|
|
|
|
ddaniel987
Newbie
Karma: +1/-0
Offline
Posts: 6
|
|
« Reply #635 on: May 03, 2024, 10:06:44 AM »
|
|
|
Thank you, u a legend!! How do I make it pop on neutral when I dont have TVSAG0 in my firmware?
|
|
|
|
|
Logged
|
|
|
|
akitossgti
Newbie
Karma: +0/-1
 Online
Posts: 7
|
|
« Reply #636 on: July 16, 2024, 10:37:34 PM »
|
|
|
Continuing with the thread of this post which is very interesting, could someone explain to me how it works in itself dnwek I attached a photo of funktionsrahmen me17.5 but I suppose that for many me17 will be worth it
|
|
|
|
|
Logged
|
|
|
|
soykii
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #637 on: July 26, 2024, 05:57:40 PM »
|
|
|
Hello Guys i have a problem with a med9.1.2 ecu i hope someone can help me or guide me to the right direction
I tryed to activate pop and bangs over the A/C button for this i changed
DNWEK to 8000rpm
Kftvsa/kftvsagi all to zero
KFZWM all maps in the low load to -25 from 6000rpm to 2500rpm
It pop and bangs really loud when i let the Pedal in the range 4000-6000rpm but around 3800rpm its stops but i can see in the cluster fuel is added the car accelerates slowly. When i push the AC button the car brakes i can feel it.
I logged the values and there i can see the timing jumps from negative to positiv and the pops are over.
When i push the button for example at 3000rpm and activate the AC it bangs for a few seconds after this i must push the button for the next time to make it this pop an bangs.
I hope someone can help
|
|
|
|
|
Logged
|
|
|
|
Somebody
Newbie
Karma: +0/-0
Offline
Posts: 13
|
|
« Reply #638 on: August 21, 2024, 06:04:28 PM »
|
|
|
Just discovered this special thread about the topic. Tried to find and modify the following maps: CWSAWE - 158A9 KFZWMN - 137B8 KFZWMNST - 13896 KFTVSA - 196FE KFTVSAKAT - not exist in this firmware DNWEK - 158AF KFZW - 0x164C1 KFZWOP - 0x15B85 KFZWOP2 - 0x15C35 Can someone take a look at this and confirm that I have found the right maps? (and have made the correct changes) I haven't tested it on the vehicle yet. Thanks  |
|
|
|
|
Logged
|
|
|
|
fc320v
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #639 on: December 08, 2024, 06:53:08 PM »
|
|
|
can anyone helo me find cwsawe and kfzwmn in this vr6 12v me7.1 file? Im still lost on how to find maps and ive dug and dug for anyone else asking this question anywhere. thanks in advance!
|
|
|
|
|
Logged
|
|
|
|
fc320v
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #640 on: December 08, 2024, 07:04:40 PM »
|
|
|
sorry, chose the wrong file.
|
|
|
|
|
Logged
|
|
|
|
rysiektr
Full Member
Karma: +3/-3
Offline
Posts: 52
|
|
« Reply #641 on: February 18, 2025, 03:18:08 PM »
|
|
|
sorry, chose the wrong file.
check this, X axles is RPM |
|
|
|
|
Logged
|
|
|
|
|
