NefMoto > Technical > Tuning > Maps study for Mini Cooper R50 and R53 Siemens EMS2000
Pages: 1 ... 6 7 [8] 9
« previous next »
Author Topic: Maps study for Mini Cooper R50 and R53 Siemens EMS2000  (Read 79765 times)
biskup
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 4
« Reply #105 on: November 22, 2020, 02:02:22 PM »
Hello Everyone,
I decided not to open a new thread.
As a hobby I modified my 2003 mini cooper r53 with smaller compressor pulley (I made & install ~15% pulley). As a next step I want to adjust sw. I use a torque lite to for logging & AEM wideband.
With help of Adriancl posts I identified few maps and make a modification in base ignition map, “throttle map”, and fuel map.
As long as the first two seem correct (I can see changes in the logs), I have a problem with fuel. I started to suspect that I did not identified fuel map correctly. Despite the changes I made, I didn’t notice AFR change at WOT. Which is definitely too high, especially between 2000-4500 rpm AFR~13,5 goes to 12,5 at higher rpm. Would you please advice? Is the map correct?
Logged
Mclain
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 16
« Reply #106 on: November 22, 2020, 02:46:08 PM »
Get x4log. It's special mini software that will let you log airmass and serial afr. Gives you the exact data that are In the axis.
Logged
biskup
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 4
« Reply #107 on: November 23, 2020, 02:36:57 AM »
Quote from: Mclain on November 22, 2020, 02:46:08 PM
Get x4log. It's special mini software that will let you log airmass and serial afr. Gives you the exact data that are In the axis.
You mean SCT X4 Interface? Would be useful to read the load in the same units as in the ecu...
But most importantly, is it the right map for fuel enrichment at full load? I changed this map significantly but AFR did not change.
Logged
Mclain
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 16
« Reply #108 on: November 23, 2020, 03:11:22 AM »
Nope,  not the interface.

This software

https://www.youtube.com/watch?v=DRSOJX57VSw&ab_channel=WarwickDean
Logged
biskup
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 4
« Reply #109 on: November 23, 2020, 05:50:20 PM »
Thanks for the link. Looks like great tool for mini. I'm considering it, but I need to correctly identify the maps first.
Logged
Alex90
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 4
« Reply #110 on: November 29, 2020, 11:54:02 AM »
i need also info about this ecu, any start map address file ??
Logged
biskup
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 4
« Reply #111 on: November 29, 2020, 02:17:44 PM »
Alex,
Software: 740903003EST6
Map start Address:7CB42 ( as on screenshot)
Org bin attached.
I still did not solve the problem with fuel...
Logged
Tomba
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 1
« Reply #112 on: April 15, 2021, 12:38:45 PM »
Does somebody know the VE map on this ECU? As it only has a pressure sensor and IAT and no MAF I wonder how the ECU calculates airmass in the cylinder.
I have an OLS file for another variant which seems to use a MAF.
Currently I have a car with different camshafts and smaller pulley. At full load it runs lambda 1.1 in midrange. Anyone who has a good mappack, please pm me.
Logged
pieros_net
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 39
« Reply #113 on: July 31, 2021, 07:38:45 AM »
HI guys,
someone finalize a mappack of this ecu?

im looking for it....

thank you brothers
Logged
adriancl
Jr. Member
**

Karma: +3/-4
Offline Offline

Posts: 30
« Reply #114 on: July 31, 2021, 01:24:21 PM »
Quote from: Tomba on April 15, 2021, 12:38:45 PM
Does somebody know the VE map on this ECU? As it only has a pressure sensor and IAT and no MAF I wonder how the ECU calculates airmass in the cylinder.
I have an OLS file for another variant which seems to use a MAF.
Currently I have a car with different camshafts and smaller pulley. At full load it runs lambda 1.1 in midrange. Anyone who has a good mappack, please pm me.

This is the map you looking for
Logged
pieros_net
Jr. Member
**

Karma: +1/-0
Offline Offline

Posts: 39
« Reply #115 on: August 02, 2021, 04:20:08 AM »
Very nice your mappack! Good…when I’m ready for mod file I will take even it by you
Logged
Tb205gti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 52
« Reply #116 on: January 20, 2023, 01:53:55 PM »
Bringing an old thread back to live.

I'm trying to get the JCW 380ml injectors to work on my 170BHp - I have the deadtime map (8x1) and the corresponding axis for voltage (5.98-16.03V).
What i just can't find is the pesky 1x1 injector scalar. Any hints as to where to find it?

(Could be a JCW210 file on same sw as a 170Bhp - then I can start hunting)
Logged
peterlundorf
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 6
« Reply #117 on: February 05, 2023, 04:00:28 AM »
Dear R53-people

I've just bought my first Mini R53 and are planning to do some DIY changes in the maps myself via TunerProRT.
However I need to build an XDF-file first with the maps/adresses etc.

Anyone who happens to have the XDF file for the R53? Or a list of map locations and table sizes?
I would deeply appreciate it.

I will of course share the xdf and my experiences when done :-)

Thanx!!
Logged
Tb205gti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 52
« Reply #118 on: June 24, 2024, 10:45:53 AM »
Quote from: Tb205gti on January 20, 2023, 01:53:55 PM
Bringing an old thread back to live.

I'm trying to get the JCW 380ml injectors to work on my 170BHp - I have the deadtime map (8x1) and the corresponding axis for voltage (5.98-16.03V).
What i just can't find is the pesky 1x1 injector scalar. Any hints as to where to find it?

(Could be a JCW210 file on same sw as a 170Bhp - then I can start hunting)

Just an update - since everybody that knows of the EMS2K are extremely tightliipped.. Smiley

I found the scalar, and the format for it. Tested with 380ml injetors as well as 550's.

Also found a ton of other maps - but still missing the "off throttle ignition advance". I can see in my logs that ignition goes to -9 when lifting, but I cannot find that map..

Is is a 2d or a linearisation?
Logged
Tb205gti
Full Member
***

Karma: +0/-0
Offline Offline

Posts: 52
« Reply #119 on: June 24, 2024, 01:50:25 PM »
Quote from: Tb205gti on June 24, 2024, 10:45:53 AM
Just an update - since everybody that knows of the EMS2K are extremely tightliipped.. Smiley

I found the scalar, and the format for it. Tested with 380ml injetors as well as 550's.

Also found a ton of other maps - but still missing the "off throttle ignition advance". I can see in my logs that ignition goes to -9 when lifting, but I cannot find that map..

Is is a 2d or a linearisation?

So let's start sharing Smiley

for my HW/SW (EMS2K, sw: 740904003EST3) Scalars is at 70D50 (16 bit LoHi, factor: 0.000030503175, format: ms/(mg/stroke)) Deadtime compensation is at 7C972, 8x1 16 bit LoHI, factor: 0,004. format: compensation in ms, Axis is voltage from 5.98v to 16.03v. (8bit @ 745FD).

Standard Cooper S: 0,015748 ms/(mg/stroke)
JCW: 0,014911 ms/(mg/stroke)

The value for 440 and 550 can be calculated. Remember that the Mini uses 3.5bar fuel pressure, not 3bar!
Logged
Pages: 1 ... 6 7 [8] 9
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • November 22, 2024, 09:46:45 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.023 seconds with 17 queries. (Pretty URLs adds 0.001s, 0q)