Pages: [1] 2
Author Topic: torque intervention can go timing to -11 degree?  (Read 4684 times)
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139


« on: November 30, 2022, 06:53:47 AM »

Hi all.
Somebody can tell me if torque intervention can go timing to -11 degree?
I have a load actual over specified and request load but boost is under boost desire. I know i must rectify this but the timing foes down very very much. I have in KFZW/2 at that cell a 12 degree but it goes to -10!
Is it a torque intervention or a hardware problem?
mifa , mrfa, misol are all ok
Thanks
Logged
rogerius
Full Member
***

Karma: +62/-6
Offline Offline

Posts: 116


« Reply #1 on: November 30, 2022, 07:23:50 AM »

log B_mibeg to see if tq interv is active
Logged
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139


« Reply #2 on: November 30, 2022, 08:23:56 AM »

Thanks Rogerius.
MIBEG is active (=1) in that area. but so much timing cut -10 degree?
Logged
Blazius
Hero Member
*****

Karma: +89/-40
Offline Offline

Posts: 1282



« Reply #3 on: November 30, 2022, 10:12:30 AM »

Jesus Christ man.



So any reason you didnt post the log, just the screenshots? You say torque values are okay but I wanna see it myself, how can I do that, without logs, ffs.


If this is a WOT run then you shouldnt have any torque intervention except from extremely poorly tuned IRL and IOP anything but its all guessing till you post the log..
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #4 on: November 30, 2022, 01:13:45 PM »

You know the rules. Please stop ignoring them. You're already on thin ice as it is
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139


« Reply #5 on: November 30, 2022, 01:41:41 PM »

I attached the log.
Logged
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #6 on: November 30, 2022, 03:29:19 PM »

Yes, your IOP and IRL are not correct, or your MAF scaling is way off.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #7 on: November 30, 2022, 03:55:16 PM »

ps_w looks reasonable. Something else in your ps -> load path is messed up, or torque request vs load request vs actual load (IRL/IOP)
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139


« Reply #8 on: December 01, 2022, 01:47:21 AM »

Thanks for answers.
So much timing CUT -10degree at torque intervention?
Other thing witch looks strange for me is lambda control witch goes down , 0.75. LTFT is -1.6 and STFT works between -10 and +10. I will try to work with FKKVS because i don;t understood yet how must i adjust  KFKHFM. Can use the same procedure like FKKVS?
MLHFM are scaled exactly like S4 with case 83mm.
I will touch IRL and IOP again and URL , because i saw a big difference between maf and maf at throttle.
I touched WDKUGDN , rised with 10% after 2500rpm few days ago , but i don't think  problem is from there.
I will rise URL!
Logged
IamwhoIam
Hero Member
*****

Karma: +52/-115
Offline Offline

Posts: 1070


« Reply #9 on: December 01, 2022, 07:48:25 AM »

Sure, keep changing 10 variables at the same time then coming back here to ask wtf could be wrong.
Logged

I have no logs because I have a boost gauge (makes things easier)
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139


« Reply #10 on: December 01, 2022, 08:11:46 AM »

Sure, keep changing 10 variables at the same time then coming back here to ask wtf could be wrong.

Did you understood the question???
Logged
IamwhoIam
Hero Member
*****

Karma: +52/-115
Offline Offline

Posts: 1070


« Reply #11 on: December 01, 2022, 08:42:19 AM »

Was there ONE question there or 15?
Logged

I have no logs because I have a boost gauge (makes things easier)
vvt18
Full Member
***

Karma: +2/-74
Offline Offline

Posts: 139


« Reply #12 on: December 01, 2022, 08:43:43 AM »

You populate the topic with nothing , like all your answers from this forum. I think you had a lot of time to do nothing!
Logged
_nameless
Hero Member
*****

Karma: +342/-466
Online Online

Posts: 2802



« Reply #13 on: December 01, 2022, 10:00:49 AM »

You populate the topic with nothing , like all your answers from this forum. I think you had a lot of time to do nothing!

Lol piss off the people who can actually help you. That will get you far here... Not.
Logged

Giving your mom a tuneup
nyet
Administrator
Hero Member
*****

Karma: +607/-168
Offline Offline

Posts: 12270


WWW
« Reply #14 on: December 01, 2022, 11:16:37 AM »

Did you understood the question???

Yes, do the opposite of what you are doing.

Return as much as possible back to stock immediately. Change one thing at a time.

Make sure your IOP/IRL make sense.
Logged

ME7.1 tuning guide
ECUx Plot
ME7Sum checksum
Trim heatmap tool

Please do not ask me for tunes. I'm here to help people make their own.

Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your ex
Pages: [1] 2
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.02 seconds with 15 queries. (Pretty URLs adds 0s, 0q)