NefMoto > Technical > Tuning > The Volvo ME7 thread:
Pages: 1 ... 193 194 [195]
« previous next »
Author Topic: The Volvo ME7 thread:  (Read 1871122 times)
Caide
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #2910 on: April 06, 2026, 10:05:10 PM »
Quote from: keichi on March 29, 2026, 06:44:21 AM
0x18FB3
Bitflipping to 0 keeps the neutral limiter
Logged
keichi
Full Member
***

Karma: +11/-2
Offline Offline

Posts: 105
« Reply #2911 on: April 07, 2026, 05:19:28 AM »
Quote from: Caide on April 06, 2026, 10:05:10 PM
Bitflipping to 0 keeps the neutral limiter
What do you mean by "neutral limiter"? What rpm do you hit, at which gear level position?
Logged
Caide
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #2912 on: April 08, 2026, 05:36:02 AM »
Quote from: keichi on April 07, 2026, 05:19:28 AM
What do you mean by "neutral limiter"? What rpm do you hit, at which gear level position?
The 4000RPM limiter in N and P, I can adjust that easily enough by changing 0x01B5AE and 0x01B5BE, but I believe there are torque limits on these gears as well. as I undertand it chaging AUTGET from 1 to 0 will switch to a manual map instead
Logged
keichi
Full Member
***

Karma: +11/-2
Offline Offline

Posts: 105
« Reply #2913 on: April 09, 2026, 06:36:02 AM »
Quote from: Caide on April 08, 2026, 05:36:02 AM
The 4000RPM limiter in N and P, I can adjust that easily enough by changing 0x01B5AE and 0x01B5BE, but I believe there are torque limits on these gears as well. as I undertand it chaging AUTGET from 1 to 0 will switch to a manual map instead


0x1B5AE is rev-limiter for gear 0 (N/P) when autget=1 and speed sensor error. Its limp-home map. No need to touch that.
0x1B5BE is "normal" rev limiter for gear 0. But that one is independent of autget.

Just change 0x1B5BE and that's all. No rev limiter on neutral regardless the gearbox.
Logged
Caide
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #2914 on: April 09, 2026, 10:37:50 PM »
Quote from: keichi on April 09, 2026, 06:36:02 AM
0x1B5AE is rev-limiter for gear 0 (N/P) when autget=1 and speed sensor error. Its limp-home map. No need to touch that.
0x1B5BE is "normal" rev limiter for gear 0. But that one is independent of autget.

Just change 0x1B5BE and that's all. No rev limiter on neutral regardless the gearbox.
This is for a manual swap, would just lifting the rev limiter work or would there also be boost/torque limits if the ECU is always in gear "0"?
Logged
keichi
Full Member
***

Karma: +11/-2
Offline Offline

Posts: 105
« Reply #2915 on: April 12, 2026, 05:15:27 AM »
Quote from: Caide on April 09, 2026, 10:37:50 PM
This is for a manual swap, would just lifting the rev limiter work or would there also be boost/torque limits if the ECU is always in gear "0"?


Lifting rev limiter would... lift rev limiter.
With ATCONF=1 TCM sends CAN requests to ECM to limit torque in certain conditions.
With ATCONF=0 ECM limit torque based on fixed values (on each gear) - usually on stock sw 1st gear only.
Logged
Caide
Newbie
*

Karma: +0/-0
Offline Offline

Posts: 7
« Reply #2916 on: April 13, 2026, 11:11:48 AM »
Quote from: keichi on April 12, 2026, 05:15:27 AM
Lifting rev limiter would... lift rev limiter.
With ATCONF=1 TCM sends CAN requests to ECM to limit torque in certain conditions.
With ATCONF=0 ECM limit torque based on fixed values (on each gear) - usually on stock sw 1st gear only.
Sorry I think there is some confusion, I was trying to say that 0x18FB3 is not ATCONF as switching it keeps the auto characteristics, so failing finding ATCONF I was looking to modify the bin to work as a manual
Logged
s60rawr
Full Member
***

Karma: +22/-1165
Offline Offline

Posts: 192



WWW
« Reply #2917 on: April 16, 2026, 06:22:39 PM »
for manual swaps why not just flash the correct base software for that  motor / trans combo? then edit the cem config. and bam.
then get to tuning like normal on there.

ya'll overcomplicate shit like its rocket science.
Logged
Quote from: dream3R on August 04, 2011, 11:02:11 AM

There is a free flash suite in progres

http://www.openmoose.net/blog/?page=renatus

#1 Nefmoto -Karma Sponge!
keichi
Full Member
***

Karma: +11/-2
Offline Offline

Posts: 105
« Reply #2918 on: Yesterday at 07:27:15 AM »
Quote from: Caide on April 13, 2026, 11:11:48 AM
Sorry I think there is some confusion, I was trying to say that 0x18FB3 is not ATCONF as switching it keeps the auto characteristics, so failing finding ATCONF I was looking to modify the bin to work as a manual

0x18FB3 is ATCONF for 100%

What do you mean by "switching it keeps the auto characteristics"?

Just set ATCONF=0 and that basically makes the whole tune MAN version.
All other maps has tiny almost not relevant differences between MAN/AUT tunes.
Logged
Pages: 1 ... 193 194 [195]
  Print  
« previous next »
 
Jump to:  

Navigation
Personal Tools
  • April 18, 2026, 02:45:18 AM
  • Welcome, Guest. Please login or register.
    Did you miss your activation email?

    Login with username, password and session length
Search
 
Advanced Search
About Disclaimer
All Rights Reserved 2010 Nefarious Motosports
Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.032 seconds with 16 queries. (Pretty URLs adds 0s, 0q)