vwdenisvw
Jr. Member
Karma: +2/-0
 Offline
Posts: 26
|
 |
« Reply #1305 on: November 25, 2020, 03:53:15 AM »
|
|
|
Edited a few more maps - KFLBTS, KFZW, KFLDHBN, LDRXN. While coldly raised the peak values of KFLDHBN - by 6000 rpm now 1 bar. https://www.youtube.com/watch?v=nd71jpKhMhk&t=1sThe afr is not regulated under the KFLBTS map. The correction is based on the intake temperature. When the temperature is more than 40 ° C - afr 0.75. Probably there is an additional protection map. Have to tune in to LAMFA... |
|
|
|
|
Logged
|
Volvo S60 2001 2.0T=>2.3T5
|
|
|
vwdenisvw
Jr. Member
Karma: +2/-0
Offline
Posts: 26
|
|
« Reply #1306 on: November 25, 2020, 03:57:24 AM »
|
|
|
It's for overboost. But overboost is disabled in our BINs.
At factory defaults of DLAMOB parameters, afr changes to 0.75. Setting all values to the minimum of 0.0469 does not change afr. Always 1. |
|
|
|
|
Logged
|
Volvo S60 2001 2.0T=>2.3T5
|
|
|
|
prometey1982
|
|
« Reply #1307 on: November 26, 2020, 03:45:11 AM »
|
|
|
At factory defaults of DLAMOB parameters, afr changes to 0.75. Setting all values to the minimum of 0.0469 does not change afr. Always 1.
If I found the map correcly then all my DLAMOB map is zero. |
|
|
|
|
Logged
|
|
|
|
|
prometey1982
|
|
« Reply #1308 on: November 26, 2020, 03:48:06 AM »
|
|
|
Also values of this map substract from lamfa_w. If I found it correcly again)) ROM:0008AAE6 loc_8AAE6: ; CODE XREF: LAMFAW+5Aj
ROM:0008AAE6 ; LAMFAW+74j
ROM:0008AAE6 jnb word_FD7C.13, loc_8AB10
ROM:0008AAEA mov r12, #1C4Bh
ROM:0008AAEE mov r13, #6
ROM:0008AAF2 movbz r14, nmot40
ROM:0008AAF6 calls 4, LookupI_41cee ; References a lookupI table
ROM:0008AAFA movbz r4, rl4
ROM:0008AAFC shl r4, #5
ROM:0008AAFE mov r5, r9
ROM:0008AB00 sub r5, r4
ROM:0008AB02 jmpr cc_NC, loc_8AB06
ROM:0008AB04 mov r5, #0
ROM:0008AB06
ROM:0008AB06 loc_8AB06: ; CODE XREF: LAMFAW+94j
ROM:0008AB06 extp #0C1h, #1 ; '+'
ROM:0008AB0A mov lamfa_w, r5
ROM:0008AB0E jmpr cc_UC, loc_8AB18
ROM:0008AB10 ; ---------------------------------------------------------------------------
ROM:0008AB10
ROM:0008AB10 loc_8AB10: ; CODE XREF: LAMFAW:loc_8AAE6j
ROM:0008AB10 extp #0C1h, #1 ; '+'
ROM:0008AB14 mov lamfa_w, r9
ROM:0008AB18
ROM:0008AB18 loc_8AB18: ; CODE XREF: LAMFAW+A0j
ROM:0008AB18 mov r8, [r0+]
ROM:0008AB1A mov r9, [r0+]
ROM:0008AB1C rets
ROM:0008AB1C ; End of function LAMFAW
|
|
|
|
|
Logged
|
|
|
|
|
prometey1982
|
|
« Reply #1309 on: November 26, 2020, 03:58:27 AM »
|
|
|
At factory defaults of DLAMOB parameters, afr changes to 0.75. Setting all values to the minimum of 0.0469 does not change afr. Always 1.
Ok. I found your problem. DLAMOB in your file is wrongly defined. It should be like in bottom picture. |
|
|
|
|
Logged
|
|
|
|
vwdenisvw
Jr. Member
Karma: +2/-0
Offline
Posts: 26
|
|
« Reply #1310 on: November 28, 2020, 01:39:11 PM »
|
|
|
Ok. I found your problem. DLAMOB in your file is wrongly defined. It should be like in bottom picture.
Damn. Big thanks for information. But there is a problem with the axis. I'm confused something... Configured AFR on LAMFA. Everything works fine. You were right. Now air consumption is 915-920 kg/h. I think that's about 280hp+. |
|
|
|
|
Logged
|
Volvo S60 2001 2.0T=>2.3T5
|
|
|
vwdenisvw
Jr. Member
Karma: +2/-0
Offline
Posts: 26
|
|
« Reply #1311 on: November 28, 2020, 01:49:54 PM »
|
|
|
Also values of this map substract from lamfa_w. If I found it correcly again))
So it can still be used. Looking at ida, I still feel like a ram ... but I hope after a while I will correct this situation)) |
|
|
|
|
Logged
|
Volvo S60 2001 2.0T=>2.3T5
|
|
|
vwdenisvw
Jr. Member
Karma: +2/-0
Offline
Posts: 26
|
|
« Reply #1312 on: November 28, 2020, 02:02:31 PM »
|
|
|
Purely my speculation.
Volvo ME7 only adjusts afr on the iat. Doesn't even pay attention to EGT. VAG also has protection in the form of a KFLBTS map. And it doesn't work for us ... For what? Therefore, motors die, especially in R from.
A drop in fuel pressure or incorrect readings from the sensors...while the liner))
|
|
|
|
|
Logged
|
Volvo S60 2001 2.0T=>2.3T5
|
|
|
daniel2345
Full Member
Karma: +11/-7
Offline
Posts: 188
|
|
« Reply #1313 on: November 28, 2020, 02:20:23 PM »
|
|
|
The emission strategy requires the engine to stay at Lambda 1.0 whenever possible. Thatswhy LAMFA is always 1.0. KFLBTS is used to protect hardware, but with factors and conditions. IAT of course, knock, etc. EGT is bad modelled at the early Modells. Engines die because stupid morons change stuff like exhaust and intercooler and expect ME7 to handle that under any condition. Putting minimum or no money on maintenance or known critical parts along with using cheapest fuel available does the rest. If engine still not blasted, people with absolutely no knowledge of basic electronics "share" files in the internet and use chinese clones to be "Chiptuners" in their hood  So please don't speculate too much  |
|
|
|
|
Logged
|
|
|
|
|
prometey1982
|
|
« Reply #1314 on: November 28, 2020, 11:11:18 PM »
|
|
|
Damn. Big thanks for information. But there is a problem with the axis. I'm confused something...
Configured AFR on LAMFA. Everything works fine. You were right.
Now air consumption is 915-920 kg/h. I think that's about 280hp+.
Here is your DLAMOB axis. |
|
|
|
|
Logged
|
|
|
|
|
prometey1982
|
|
« Reply #1315 on: November 28, 2020, 11:20:09 PM »
|
|
|
Purely my speculation.
Volvo ME7 only adjusts afr on the iat. Doesn't even pay attention to EGT. VAG also has protection in the form of a KFLBTS map. And it doesn't work for us ... For what? Therefore, motors die, especially in R from.
A drop in fuel pressure or incorrect readings from the sensors...while the liner))
TABGBTS in your file has 950 grad value. R motor's TABGBTS has 500 grad value. This is why your KFLBTS map doesn't use for lambda calculations. About R motors. They die due to lowering performance of fuel pumps. Unfortunately Volvo doesn't catch a problem with bad lambda and doesn't switch car to limp mode. |
|
|
|
|
Logged
|
|
|
|
|
|
|
prometey1982
|
|
« Reply #1317 on: November 30, 2020, 10:12:06 AM »
|
|
|
Also I have to create 5120 hack for Volvo ME7. My current hardware config doesn't allow me to accelate 0-100km/h less than 6 secs with 1.5 bar boost.
|
|
|
|
|
Logged
|
|
|
|
Rolle1974
Jr. Member
Karma: +0/-0
Offline
Posts: 25
|
|
« Reply #1318 on: November 30, 2020, 03:37:19 PM »
|
|
|
Try to find NMAXDV (engine speed limit at fault of the vehicle speed signal) on this Volvo S80 2.4t 2001. Anyone who can point out the adress for me?
Want it to go down to idle (800 rpm) in the event of a speed signal failure.
|
|
|
|
|
Logged
|
|
|
|
|
prometey1982
|
|
« Reply #1319 on: December 01, 2020, 08:52:53 AM »
|
|
|
Try to find NMAXDV (engine speed limit at fault of the vehicle speed signal) on this Volvo S80 2.4t 2001. Anyone who can point out the adress for me?
Want it to go down to idle (800 rpm) in the event of a speed signal failure.
It's not easily to found this map. Why do you need it? |
|
|
|
|
Logged
|
|
|
|
|
